Manuals / Zenoah / Lawn and Garden / Brush Cutter

Zenoah Set up BCZ3000S, MOUNTING ENGINE SE1, Connecting Throttle Wire, Connecting Switch Wires

Models: BCZ3000

1 40

Download 40 pages 38.21 Kb

Page 13

6.Set up (BCZ3000S)

6.Set up (BCZ3000S)

SE1

■MOUNTING ENGINE (SE1)

1.Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears.

2.Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult to engage, twist the engine slightly.

3.Fasten the clamp securely with two screws.

SE2

SE3

(1)

SE4

IMPORTANT

Tighten the screws gradually by turns.

■CONNECTING THROTTLE WIRE

1. Remove the air cleaner cover.

2. Connect the end of the throttle wire to the joint on the top of the carburetor. (SE2)

■CONNECTING SWITCH WIRES

•Connect the switch wires between the engine and the main unit. Pair the wires of the same color.

■INSTALLING HANDLE

•Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. (SE3)

(1) About 19 inches (48cm)

■INSTALLING DEBRIS GUARD

•Put the debris guard on the braket, attach it with the 2 screws. (SE4)

13 

Image 13

Zenoah manual Set up BCZ3000S, MOUNTING ENGINE SE1, Connecting Throttle Wire, Connecting Switch Wires, Installing Handle

Contents

BCZ3000S BCZ3000SW OWNER/OPERATOR MANUALBRUSHCUTTERS 848-JC0-93A0311Page CONTENTS SAFETY FIRSTInstructions contained in warnings within this WARNINGS IN THE MANUAL1. Parts location 2. SpecificationsBCZ3000S/BCZ3000SW Overall sizeLxWxH 4 2Wear head, eye and ear protection 3. Warning labels on the machine3Warning/Attention Never modify your brushcutter6  4. Symbols on the machineIMPORTANT ENGINE INFORMATION Use RedMax 50 1 Oil5. For safe operation 4Thick work gloves 5Non-slip-solework bootsWORKING CONDITION 1Helmet 2Ear protectorsPRODUCT, Repetitive Stress InjuryRSI could occur WORKING PLAN8  5. For safe operationSTARTING THE ENGINE BEFORE STARTING THE ENGINE9  5. For safe operation10  USING THE PRODUCT5. For safe operation IF SOMEONE COMES MAINTENANCEHANDLING FUEL 11 12  TRANSPORTATION5. For safe operation CONNECTING THROTTLE WIRE 6.Set up BCZ3000SCONNECTING SWITCH WIRES INSTALLING HANDLE1 About 14.5 inches 37cm CONNECTING THROTTLE WIRE 6.Set up BCZ3000SWMOUNTING ENGINE SE5 SE6 SE7 SE8INSTALLING DEBRIS GUARD 6.Set up BCZ3000S/BCZ3000SWINSTALLING CUTTING HEAD SE10 SE107. Fuel HOW TO MIX FUEL16  RECOMMENDED MIXING RATIO GASOLINE 50 OILFOR YOUR ENGINE LIFE, AVOID FUELING THE UNIT7. Fuel 8. Operation 4 ignition switch 5 start 6 stopOP1 OP21 STARTING ENGINE1 cable adjuster ADJUSTING IDLING SPEED OP6 ADJUSTING THROTTLE CABLE1 idle adjusting screw STOPPING ENGINE OP320  ADJUSTING THE LINE LENGTH8. Operation MAINTENANCE CHART 9. MaintenanceREFILLING TRIMMING LINE MA1 21 AIR FILTER REPLACEMENT PLUG IS A CHAMPION RZ7C1 air filter FUEL FILTER 1 fuel filter SPARK PLUGSPARK ARRESTER MUFFLER1 spark arrester GEAR CASE MA6 INTAKE AIR COOLING VENTMA71 10. Storage1cylinder 2intake air cooling vent back 24 11. Optional blade usage CHARTOPT1 CUTTEROPT2 SET UP THE BLADEOPT3 1 CoverCUTTING METHOD OPT6 OPT7 OPT8OPERATION 27 28  OPT9CONTROLLING BLADE BOUNCE 1. What causes kick outOPT10 MAINTENANCE BLADE3.How you can maintain the best control TRANSPORTING THE UNITCHECK 11. Troubleshooting guidePROBABLE CAUSES ACTION31  12. Parts listBCZ3000S BCZ3000SW BRUSHCUTTERS32  Fig.1 DRIVE UNIT BCZ3000S S/N 300001 and up12. Parts list OPTIONAL BLADE & ACCESSORIES 33 Fig.1 DRIVE UNIT BCZ3000S S/N 300001 and up 34  Fig.2 DRIVE UNIT BCZ3000SW S/N 300001 and up12. Parts list Fig.2 DRIVE UNIT BCZ3000SW S/N 300001 and up 35 OPTIONAL BLADE 36  Fig.3 ENGINE UNIT12. Parts list SPECIAL TOOLS 37 Part Number DescriptionYOUR WARRANTY RIGHTS AND OBLIGATIONS CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTManufacturer’s warranty coverage Owner’s warranty responsibilitiesRedMax LIMITED WARRANTY RedMax Garantie limitée