Husqvarna CTH155 Eng Adjustment of the cutting unit, Einstellung des Mähaggregats

Page 75

￿

AB

Eng Adjustment of the cutting unit

A. In the direction of travel

1.Check that the air pressure is correct in all four tires.

2.Make sure that the machine is on a horizontal surface.

3.Lift up the cutting unit to its highest position.

4.Measure the distances A and B.

Einstellung des Mähaggregats

A. In Fahrrichtung

1.Prüfen, daß der Luftdruck an allen vier Reifen richtig ist.

2.Prüfen, daß die Maschine auf einer ebenen Unterlage steht.

3.Mähaggregat in die oberste Lage anheben.

4.Abstände A und B messen.

2

1

Eng To achieve best cutting results the cutting unit’s front edge (B) should be about 10 mm (0.375") lower than the back edge

(A). Adjust in the following way to raise the back edge:

1.Loosen the nut (1) on both the left and right levers.

2.Screw the nut (2) the same number of turns on both levers.

3.When the correct distance (A) is obtained this setting is locked with the nut (1).

Für bestes Mähergebnis muß die Vorderkante des Mähaggregats (B) ca. 10 mm tiefer liegen als die Hinterkante

(A). Einstellung zur Erhöhung der Hinterkante:

1.Mutter (1) am linken und rechten Hebel lösen

2.Mutter (2) gleich viele Drehungen an beiden Hebeln verstellen.

3.Wenn der richtige Abstand (A) erhalten wird, sind die Einstellungen mit der Mutter (1) zu sperren.

FPour avoir le meilleur résultat de coupe, le bord avant du carter de coupe (B) doit être de 10 mm en dessous du bord arrière (A). Pour relever le bord arrière, procéder de la façon suivante:

1.Dévisser l’écrou (1) sur les supports avant gauche et droit du carter de coupe.

2.Visser exactement de la même façon les écrous (2) sur les supports avant du carter de coupe

3.Lorsque la distance (A) est correcte, bloquer le réglage

avec l’écrou (1).

75

FRéglage du carter de coupe

A. Reglage lateral

1.Vérifier que la pression est correct dans les quatre pneus.

2.S’assurer que la machine est sur un terrain plat.

3.Relever le carter de coupe dans la position la pus haute.

4.Mesurer les distances A et B.

Esp Ajuste de la unidad de corte

A. En el sentido de la marcha

1.Controlar que la presión de inflado es la correcta en los cuatro neumáticos.

2.Asegurarse de que la máquina está sobre suelo horizon- tal.

3.Levantar la unidad de corte hasta su posición más elevada.

4.Medir la distancia A y B.

Regolazione del tagliaerba

A. Nel senso di marcia

1.Controllare la pressione dei pneumatici.

2.La macchina deve essere in piano.

3.Sollevare al massimo il tagliaerba.

4.Misurare le distanze A e B.

NL Het instellen van de maaikast

A. In de rijrichting

1.Controleer of de luchtdruk in alle vier de banden juist is.

2.Zorg ervoor dat de machine op een vlakke ondergrond staat.

3.Zet de maaikast in de hoogste stand.

4.Meet de afstanden A en B.

Esp Para obtener el mejor resultado de corte, el extremo delantero

(B)de la unidad de corte ha de estar unos 10 mm (0,375") más bajo que el extremo posterior (A). Ajustar de la manera siguiente para elevar el extremo posterior:

1.Quitar la tuerca (1) en las palancas izquierda y derecha.

2.Enroscar la tuerca (2) el mismo número de vueltas en las dos palanca.

3.Cuando se ha obtenido la distancia correcta (a), el ajuste se bloquea con la tuerca (1).

Per ottenere i migliori risultati, il bordo anteriore del tagliaerba

(B)deve essere circa 10 mm più basso di quelo anteriore (A). Regolare nel modo sequente:

1.Allentare il dado (1) sui bracci destro e sinistro.

2.Avvitare il dado (2) di un nuemero identico di giri sui due bracci.

3.Dopo aver raggiunto la distanza corretta (A) bloccare stringendo il dado (1).

NL Om het beste maairesultaat te bereiken, dient de voorkant (B) van de maaikast ca. 10 mm (0,375") lager te staan dan de achterkant (A). Ter verhoging van de achterkant als volgt instellen:

1.Draai moer (1) los op linker en rechter hefboom.

2.Draai moer (2) op de beide hefbomen evenveel slagen.

3.Wanneer de juiste afstand (A) is bereikt, wordt de instelling met de moer (1) vastgezet.

Image 75
Contents Manual de las instrucciones Manuel d’instructionsManuale di istruzioni AnleitungshandbuchPage III. Operation Safety RulesEng I. Training II. PreparationIV. Maintenance and Storage III. Betrieb SicherheitsvorschriftenSchulung II. VorbereitungIV. Wartung UND Lagerung III. Utilisation Règles de SécuritéPrécautions Dutilisation II. PréparationIV. Entretien ET Entreposage III. Operación Reglas De SeguridadInstrucción II. PreparaciónIV. Mantenimiento Y Almacenamiento III. Funzionamento Norme AntinfortunisticheAddestramento ALL’USO II. PreparazioneIV. Manutenzione E Periodi DI INATTIVITA’ III. Bediening VeiligheidsregelsNL I. Training II. VoorbereidingIV. Onderhoud EN Opslag Neutral Atención Unverzüglich MIT Lenkrad Steering WheelAlbero DI Estensione NL HET Stuur Volant DE DirectionArbre D’EXTENSION EJE DE Extención VolanteSedile SitzSiège Esp AsientoHinweis RemarqueNota Installazione della batteria NL Accu installeren Instalación de la bateríaQuite el tapador del acumulador Discharge Chute Nut Flat Washer Eng To install bagger components to tractorTo assemble and install mulcher plug Bagger adjustmentHorizontal adjustment Vertical adjustmentInstallation der Aufhängung der Grasfangbox des Traktors Seitenjustierung Montage und Installation des MulcheinsatzesMontage der Grasfangbox Justieren der GrasfangboxAssemblage des composants du collecteur Réglage vertical Adjustement du collecteurPour assembler le collecteur Réglage horizontal8x63,5mm arandelas planas Tuercas de 3/8 Arandelas planas Descarga de adaptarseAjuste vertical Esp Para montar el contenedorRegulacion del contenedor Ajuste horizontalPer montare i componenti del cesto di raccolta Regolazione orizzontale Per Iinstallazione del Kit MulchingPer montare il cesto di raccolta Regolazione del cestoSluitring Horizontale bijstelling Het monteren en installeren van de mulchplugNL De grascontainer monteren Afstellen van grascontainerNL Peilwielen Afstellen Einstellen DER TasträderPour Régler LES Supports DE Roue Regolazione DEI Ruotini AnterioriSchnelles Heben und Senken des Mähaggregats NL De plaats van de bedieningsorganen Emplacement des commandesEsp Ubicación de los mandosè ComandiAcceleratore Commande de gazGashebel AceleradorEsp 3. Pedal de freno y de embrague Eng 3. Brake and clutch pedalBrems- und Kupplungspedal Pédale de frein et d’embrayageEsp 4. Acoplamiento/desacoplamiento de la transmisión Embrayage et débrayage de la boîte de vitessesEng 4. Motion control lever Ein- und Ausschalten des AntriebesSollevamento/abbassamento del tagliaerba Eng 6. Quick lifting/lowering of the cutting unitSchnelles Heben und Senken des Mähaggregats CorteSerrure de contact Eng 7. Ignition LockEsp 7. Cerradura de encendido ZündschloßNL 8. Parkeerrem Frein de parkingEsp 8. Freno de estacionamiento Freno di parcheggioEsp 10. Ajuste de la altura de corte Eng 10. Cutting height setting10. Mähhöheneinstellung 10. Réglage de la hauteur de coupeEsp Reposición de combustible Eng Filling upTanken Plein d’essenceEsp Nivel de aceite Eng Oil levelÖlstand Niveau d’huileEsp Presión de inflado de los neumáticos Eng Tire air pressureReifendruck Pression de gonflage des pneusAvviamento del motore Driving . Betrieb . Conduite . Conducción Guida . RijdenAnlassen des Motors Démarrage du moteurRemarque Eng IMPORTANT! Cold Starting for Hydro Eng Purge TransmissionEntlüften DES Getriebes Purger LA TransmissionEsp Purgar LA Transmisión Spurgo Della TrasmissioneNL Transmissie Ontluchten Esp Conducción Eng DrivingBetrieb ConduiteEsp Consejos para el corte Eng Cutting tipsRatschläge zum Rasenmähen Conseils de tonteEsp Para vaciar la cargadora Eng To Dump BaggerEntleeren der Grasfangbox Pour vider le bacPour passer dune fonction à lautre Eng To convert mowerEsp Para cambiar el ajuste de la segadora Regolazione della funzione di taglioNL De Maaier Ombouwen Pericolo Eng WarningWarnung Esp AdvertenciaParada del motor Eng Switching off the engineAbstellen des Motors Arrêt du moteurEsp Advertencia Arresto del motoreNL Het stoppen van de motor Eng WarningEng Engine hood MotorhaubeMotorhaube hochklappen Scheinwerferanschluß lösen NL Motorkap Capot moteurEsp Cubierta del motor Cofano MotoreManutenzione Eng MaintenanceEsp Mantenimiento WartungWartung des Motors Eng To service engineAfin de réaliser l’entretien du moteur Esp Mantenimiento del motorWartungsnachweis Service RecordInforme DE Servicio COMPE-RENDU DentretienDati DI Servizio Service AantekeningenLame Eng BladesMesserbalken Esp CuchillasEng 6 Star pattern blade Eng 5 Star pattern bladeMesserbalkenbohrung mit fünfeckige Aussparung Lame avec orifice de fixation central étoil à cinq branchesLama con foro stellare Esp Cuchilla de orificio-estrella de cinco puntasLama con for stellare a 5 punte NL Mes met 5-hoekige sterBlade Removal Esp Freno Eng BrakesBremse Reglage du FreinDesmontaje de la unidad de corte Dismantling of the cutting unitDemontage des Mähdecks Depose du Carter de CoupeMontaggio del piatto di taglio Eng Assembly of the cutting unitEinbau des Mähdecks Montage du groupe de coupeEsp Cambio de la correa propulsora del equipo de corte Eng Replacement of drive belt for cutting unitAuswechsein des Treibriemens für das Mähaggregat Changement de la courroie dentrainment du carter de coupeEsp Ajuste de la unidad de corte Eng Adjustment of the cutting unitEinstellung des Mähaggregats Réglage du carter de coupeNL LINKS/RECHTS Bijstellen Seitliche EinstellungReglage Transversal Regolazione Fianco a FiancoBoîte Eng Replacement of drive beltAuswechsein des Treibriemens Echange de la courroie dentraînement moteurTral Adjustment Eng Transaxle Motion Control Lever NEUEinstellung DES Steuerknüppels DES Schaltgetriebes DEL Movimiento DEL Cambio Mecánico Esp Regulación DE LA Palanca DE ControlRefroidissement DE LA Transmission Transaxle Pump FluidTRANSACHSEN-KÜHLUNG TRANSACHSEN-PUMPENFLÜSSIGKEITTroubleshooting Störungssuche Recherche des pannes . Búsqueda de averías Ricerca guasti . Het localiseren van fouten Etretien et réparations ServiceStorage . Aufbewahrung . Rangement . Conservación Suivre la procédure suivante une fois la saison terminéeZet de machine in een droge overdekte ruimte Rismessaggio . StallenAl termine della stagione effettuare i seguenti interventi ServizioPage Page 532 17 99-79 11.9.01 JH

CTH155 specifications

The Husqvarna CTH155 is a powerful and versatile riding mower designed to deliver exceptional performance and comfort in lawn care. This innovative machine comes equipped with several features aimed at enhancing user experience and ensuring a clean, efficient cut.

At the heart of the CTH155 is a robust engine that provides ample power for tackling tough grass conditions. The reliable engine is complemented by a smooth hydrostatic transmission, which allows for precise speed control and effortless maneuverability. This feature enables users to easily navigate around obstacles, making it ideal for yards with intricate landscaping.

The cutting deck of the Husqvarna CTH155 is designed for optimal performance. Featuring a 38-inch deck, it is equipped with three high-performance blades that ensure a clean and even cut, resulting in a healthier lawn. The adjustable cutting height provides the flexibility to choose the best setting for different grass types and environmental conditions, allowing for a tailor-made mowing experience.

One of the standout technologies featured in the CTH155 is the reverse mowing feature, which ensures that users can effectively mow in reverse without compromising safety. This is particularly useful for trimming grass in tight areas where forward mowing is not possible. The mower also boasts a tight turning radius, further enhancing its maneuverability.

Comfort is a key consideration in the design of the CTH155. It features an ergonomically designed seat that is both comfortable and adjustable, allowing users to find the perfect driving position. The user-friendly control panel provides easy access to the mower’s functions, ensuring a hassle-free operation.

Additionally, the Husqvarna CTH155 is equipped with large rear wheels, which enhance stability and traction, enabling it to handle various terrains with ease. The durable construction of this mower ensures that it can withstand the rigors of regular use while maintaining peak performance.

Overall, the Husqvarna CTH155 represents a blend of efficiency, comfort, and modern technology, making it a reliable choice for homeowners looking to maintain their lawns effortlessly. Whether it's tackling thick grass or navigating around obstacles, the CTH155 is engineered to meet the demands of lawn care enthusiasts.