Husqvarna FC2145W, FC2145S, CC2145, BC2145 manual Muffler, Cooling system, Air filter

Page 30

MAINTENANCE

2Press the start throttle lock as described under the heading Starting and stopping.

3If the start throttle speed is too low (below 4000 rpm), turn the adjuster screw A clockwise until the cutting attachment starts to rotate. Then turn A clockwise a further 1/2 turn.

4If the start throttle speed is too high, turn the adjuster screw A anticlockwise until the cutting attachment stops. Then turn adjuster screw A clockwise a further 1/2 turn.

Muffler

CAUTION! Some mufflers are fitted with a catalytic converter. See chapter on Technical data to see whether your machine is fitted with a catalytic converter.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material. Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. This is best done with a wire brush. On mufflers without a catalytic converter the mesh should be cleaned weekly, or replaced if necessary. On mufflers fitted with a catalytic converter the mesh should be checked, and if necessary cleaned, monthly. If the mesh is damaged it should be replaced. If the mesh is frequently blocked, this can be a sign that the performance of the catalytic converter is impaired. Contact your dealer to inspect the muffler. A blocked mesh will cause the machine to overheat and result in damage to the cylinder and piston.

CAUTION! Never use a machine with a defective muffler.

WARNING! Mufflers fitted with catalytic

! converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin.

Remember the risk of fire!

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

4

3

2 1

The cooling system consists of:

1Air intake on the starter.

2Fins on the flywheel.

3Cooling fins on the cylinder.

4Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts.

•Excessive fuel consumption.

Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents FC2145 FC2145S BC2145 FC2145W CC2145 KEY to Symbols SymbolsContents Introduction Dear CustomerWhat is WHAT? What is what on the brush cutter? BCDecompression valve FC 2145 S, FC 2145 W What is what on the brush cutter? CC General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutVibration damping system Stop switchCutting attachment guard Quick releaseMuffler Locking nutCutting equipment Cutting equipmentLocking screw General rulesBent, twisted, cracked, broken or Sharpening grass cutters and grass bladesSharpening the saw blade To straighten a twisted blade so that itTrimmer head Assembly Assembling the handlebar and throttle BC 2145, CCTransport position, handlebar Assembling the cutting equipmentFitting the blade guard and saw blade Fitting the trimmer guard and trimmer head Trimmy SII Fitting other guards and cutting attachmentsAdjusting the harness and brush cutter Standard harnessVector harness Correct balance Fuel safety Fuel HandlingFuel Fuelling MixingStarting and stopping Starting and StoppingCheck before starting Cold engineHeated handles FC 2145 W StartingStopping Starter cord around your handGeneral working instructions Basic safety rulesWorking Techniques ABC of clearingForestry clearing using a saw blade Brush cutting with a saw blade Grass clearing using a grass blade Grass trimming with a trimmer headMaintenance CarburettorMuffler Cooling systemAir filter Drive shaft Cleaning the air filterBevel gear Spark plugTemperature 5C or colder Winter useMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataChampion RCJ 6Y Approved accessories Type Cutting attachment guard, Art. no EC-declaration of conformity Applies to Europe only Poly Trim Trimmy SII Page Auto Tap n’Go 45 Spin Page Original instructions 1153306-26

FC2145W, BC2145, CC2145, FC2145S, FC2145 specifications

The Husqvarna FC2145, FC2145S, CC2145, BC2145, and FC2145W are part of a premium range of outdoor power equipment designed to cater to the diverse needs of landscaping, gardening, and recreational tasks. Each model showcases Husqvarna's dedication to innovation, durability, and user-friendly operation while ensuring high performance and efficiency.

The FC2145 series, which includes both the FC2145 and FC2145S, is primarily designed for advanced grass cutting and trimming tasks. The models are equipped with a powerful engine that provides optimal torque and energy efficiency. The ergonomic design of the handles ensures comfort during extended use, reducing fatigue. One notable feature is the lightweight construction, making them easy to maneuver around various terrains and obstacles.

In contrast, the CC2145 model is tailored for concrete and construction work. This robust machine boasts a high-torque engine and a durable chassis, ensuring it can withstand demanding job sites. Its advanced vibration dampening system minimizes user fatigue, enhancing overall productivity. Additionally, the CC2145 incorporates easy-to-use controls, making it accessible for both professionals and DIY enthusiasts.

The BC2145 is a versatile brush cutter that excels in clearing dense vegetation and underbrush. This model is known for its powerful performance and features a dual cutting system that enhances cutting efficiency. Its adjustable loop handle allows for optimal control, especially when working in tight spaces. The BC2145 also comes with a variety of cutting attachments, enabling the user to adapt to different landscaping needs seamlessly.

Lastly, the FC2145W is designed for more specialized applications, offering a dedicated approach to weed control and maintenance. This model features advanced technology that allows for precision cutting, minimizing damage to adjacent plants. Its water-resistant design enhances durability in various weather conditions, making it ideal for both professional landscapers and homeowners.

In conclusion, the Husqvarna FC2145, FC2145S, CC2145, BC2145, and FC2145W models represent the brand's commitment to quality and innovation. Each model brings unique characteristics and technologies that cater to various outdoor needs, ensuring users can achieve their landscaping goals efficiently and effectively. Their blend of power, comfort, and versatility makes them indispensable tools for anyone serious about outdoor maintenance and care.
Top Page Image Contents