Husqvarna 455 RANCHER manual High speed jet H, Correctly adjusted carburettor

Page 30

MAINTENANCE

High speed jet H

At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet.

CAUTION! If the high speed jet is screwed in too far, it may damage the piston/cylinder.

When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance. The carburettor’s high speed jet is then locked using a limiter cap in the fully screwed out position. The limiter cap limits the potential to adjust the high speed jet to at most half a turn.

To adjust the carburettor correctly you should contact a mechanic with access to a rev counter.

CAUTION! As the spark is cut off, the rev counter does not show speeds higher than 13600 rpm.

Correctly adjusted carburettor

When the carburettor is correctly adjusted the machine accelerates without hesitation and 4-cycles a little at full throttle. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H-jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine.

Checking, maintaining and servicing chain saw safety equipment

Note! All service and repair work on the machine demands special training. This is especially true of the machine’s safety equipment. If your machine fails any of the checks described below we recommend that you take it to your service workshop.

Chain brake and front hand guard

Checking brake band wear

Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake.

Regularly check that the brake band is at least 0.6 mm thick at its thinnest point.

Checking the front hand guard

Make sure the front hand guard is not damaged and that there are no visible defects such as cracks.

Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover.

Checking the inertia brake release

Place the chain saw, with the engine switched off, on a stump or other stable surface. Release the front handle and let the saw fall by its own weight, rotating around the rear handle towards the stump.

When the bar hits the stump the brake should be applied.

Checking the brake trigger

Place the chain saw on firm ground and start it. Make sure the chain does not touch the ground or any other object. See the instructions under the heading Start and stop.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Rancher KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? 20 19 What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral advice on adjusting depth gauge setting Sharpening cutting teethLubricating cutting equipment Adjustment of depth gauge settingTensioning the chain Chain oilNeedle bearing lubrication Checking chain lubricationChain drive sprocket Checking wear on cutting equipmentBar Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsAlways use a fast cutting speed, i.e. full throttle Basic cutting technique GeneralTerms Limbing CuttingLog is supported at one end. There is a high risk that it Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentGeneral Correctly adjusted carburettor High speed jet HThrottle lock Muffler StarterChanging a broken or worn starter cord Tensioning the recoil spring Air filterSpark plug Changing a broken recoil springLubricating the bar tip sprocket Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationTemperature -5C or colder Air Injection centrifugal cleaningTemperature 0C or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data´z+H8h¶6S¨ 38 English´z+H8h¶6S¨ Bar and chain combinationsEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 122001, EN ISO 1140247-26 ´z+H8h¶6S¨ ´z+H8h¶6S¨
Related manuals
Manual 4 pages 16.25 Kb

455 RANCHER specifications

The Husqvarna 455 Rancher is a powerful chainsaw designed for both professional users and avid homeowners. Renowned for its robust construction and unparalleled performance, this chainsaw is an excellent choice for those who demand reliability and accuracy in their outdoor tasks.

At the heart of the 455 Rancher is its 55.5 cc X-Torq engine, which offers a perfect blend of power and fuel efficiency. This advanced engine technology reduces fuel consumption by up to 20% while simultaneously minimizing exhaust emissions, making it an environmentally conscious choice. The system also provides higher torque over a wider RPM range, ensuring that users have the power they need when cutting through larger logs or tough wood.

The 455 Rancher features a high output air filtration system, which enhances the lifespan of the chainsaw by ensuring the engine stays clean and well-protected from dust and debris. This system is particularly beneficial for users who work in dusty or challenging environments, as it requires less frequent filter cleaning and replacement.

Another notable characteristic of the Husqvarna 455 Rancher is its anti-vibration technology. This feature minimizes vibrations during operation, significantly reducing operator fatigue and enabling longer and more comfortable use. The chainsaw also comes equipped with an ergonomic design, including a well-balanced construction that allows for better maneuverability.

Safety is paramount with the 455 Rancher, which is equipped with a variety of safety features. The chain brake is a critical component that helps prevent accidental injury by halting the chain's movement in the event of kickback. Additionally, the chainsaw includes a low kickback chain designed to lessen the risk of kickback incidents while cutting.

The chainsaw boasts an adjustable oil pump that allows users to control the amount of oil delivered to the chain, ensuring optimal lubrication and extending the life of the chain and bar. Combined with an easy-to-access fuel and oil tank, the Husqvarna 455 Rancher is engineered for user convenience.

In conclusion, the Husqvarna 455 Rancher stands out for its powerful engine, efficient fuel consumption, advanced safety features, and user-centric design. Whether for professional forestry work or home landscaping projects, this versatile and durable chainsaw is a reliable tool that can tackle a wide range of cutting tasks with ease.
Top Page Image Contents