Cutting unit, Cutting height adjustment lever | Husqvarna 15V2s AWD

PRESENTATION

Cutting unit

Rider 15V2, Rider 15V2s AWD and 15V2 AWD can be equipped with two different cutting units.

•Combi 1030mm/41”

•Combi 1120 mm/44”

The Combi-unit, equipped with a BioClip-plug, ﬁnely chops the cuttings to fertiliser. Without the BioClip-plug the unit works in the same way as a rear ejection unit.

Lifting lever for the cutting unit

The lift lever is used to set the cutting unit in transport or mowing position.

If the lever is pulled backwards the unit is raised and the blades automatically stop rotating (transport position).

If the lock button is pressed in and the lever is moved forwards the unit will be lowered and the blades will automatically start to rotate (mowing position).

The lever can also be used to temporarily regulate the cutting height, e.g. for a small mound in the lawn.

Cutting height adjustment lever

The cutting height can be adjusted to 7 different positions with the cutting height lever.

14 – English

Combi-unit 40-90 mm (1 9/16” - 3 9/16”)

Lights

The lights are switched on and off using the power switch on the control panel.

Counter

The chronometer shows how many hours the engine has been running. Any time when the engine is not running but the ignition is switched on is not registered. The last digit shows tenths of an hour (6 minutes).

Seat

The seat has a jointed attachment on the front edge and can be tipped forward.

Image 14

Husqvarna 15V2s AWD Cutting unit, Lifting lever for the cutting unit, Cutting height adjustment lever, Lights, Counter

Contents

Rider 15V2 Rider 15V2 AWD Rider 15V2s AWD English Contents After the ﬁrst 8 hours Service journalPre-delivery service Driving and transport on public roads IntroductionDear Customer Towing Good service Serial Number KEY to Symbols Symbols Brake Starting instructions Insure your Rider Safety InstructionsSafety instructions General use Driving on slopes This is what you do Maintenance Children Transport What is WHAT? Location of the controls Presentation Lifting lever for the cutting unit Cutting height adjustment leverCutting unit Lights Release lever Exercise care and refuel outdoors see safety instructionsFuelling Release lever Rider 15V2 AWD Start the engine DrivingBefore starting Driving the Rider Starting the engine with a weak batteryConnecting the jump leads Remove the cables in the reverse order Other objects which can be thrown out by the blades Cutting tipsStop the engine Maintenance Maintenance schedule Removing of the machine hoods CleaningChecking and adjusting the steering wires Checking and adjusting of throttle wire Adjusting the parking brake RiderAdjusting the parking brake Rider 15V2 AWD Can result in reduced braking ability Replacing the air ﬁlter Checking and adjusting the choke wireReplacement of fuel ﬁlter Cool before starting to replace the air ﬁlter Ignition system Check the level of the battery acid Dry-charged batteryChecking the fuel pump’s air ﬁlter Replacing the spark plug Check the safety system Replacing the light bulbs Main fuse Checking the engine’s cooling air intake When the engine is running. Mind your ﬁngersChecking the tyre pressure Fitting the cutting head Removing the cutting unit Trapping your hand Replacing the cutting unit belts Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Service position for the cutting unit Placing in the service position Removing the BioClip plug Restoring from service positionChecking the blades Changing the oil ﬁlter LubricationChecking the engine’s oil level Replacing the engine oil General lubrication Lubricating the belt adjusterChecking the transmission oil level Troubleshooting schedule Problem Procedure Winter storage ServiceStorage Guard Technical data EC-declaration of conformity Applies to Europe only Page ´z+S!r¶6H¨ Page 1151018-26 ´z+S!r¶6H¨ ´z+S!r¶6H¨