Service journal, Pre-delivery service | Husqvarna 15V2s AWD specs

Service journal

Pre-delivery service

11a. Dry-charged battery (5067888-01): Top up battery with acid and charge for four hours.

1b. Wet-charged battery (5101385-01): Charge at 3 ampere for 4 hours.

2 Fit steering wheel, seat and any optional equipment.

3Check and adjust tyre pressure (60 Kpa, 0.6 bar).

4 Adjust cutting unit:

Adjust lift springs (effective weight of cutting unit should be 12-15kg / 26.5-33 lb).

Adjust cutting unit so that rear edge is about 2-4 mm / 1/8” higher than front edge.

Adjust cutting unit height setting so that cutting height limit is 5 mm / 3/16” above the frame of the unit at the lowest cutting height.

5 Check that the right amount of oil is in the engine.

6 Check that there is oil in the transmission’s oil tank.

7 Connect battery.

8 Fill with fuel and start engine.

9Check that machine does not move in neutral.

10 Check:

Forward drive.

Reverse drive.

Operation of blades.

Seat safety switch.

Lif lever safety switch.

The safety switch for the hydrostat pedals.

11Check engine speed, 2900±100 rpm.

12Tell customer about:

Needs and beneﬁts of following the service schedule.

Servicing and the inﬂuence of this journal on the second-hand value of the machine.

Range of applications for BioClip.

Complete proof of sale etc.

Pre-delivery service carried out. No outstanding problems. Certiﬁed:

Date, mileage, stamp, signature

After the ﬁrst 8 hours

1 Change engine oil

English – 3

Image 3

Husqvarna 15V2s AWD manual Service journal, Pre-delivery service, After the ﬁrst 8 hours

Contents

English Rider 15V2 Rider 15V2 AWD Rider 15V2s AWD Contents Service journal Pre-delivery serviceAfter the ﬁrst 8 hours Towing IntroductionDear Customer Driving and transport on public roads Serial Number Good service Symbols KEY to Symbols Brake Starting instructions General use Safety InstructionsSafety instructions Insure your Rider This is what you do Driving on slopes Children Maintenance Transport Location of the controls What is WHAT? Presentation Lights Cutting height adjustment leverCutting unit Lifting lever for the cutting unit Release lever Rider 15V2 AWD Exercise care and refuel outdoors see safety instructionsFuelling Release lever Driving Before startingStart the engine Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Driving the Rider Cutting tips Stop the engineOther objects which can be thrown out by the blades Maintenance schedule Maintenance Cleaning Checking and adjusting the steering wiresRemoving of the machine hoods Can result in reduced braking ability Adjusting the parking brake RiderAdjusting the parking brake Rider 15V2 AWD Checking and adjusting of throttle wire Cool before starting to replace the air ﬁlter Checking and adjusting the choke wireReplacement of fuel ﬁlter Replacing the air ﬁlter Replacing the spark plug Check the level of the battery acid Dry-charged batteryChecking the fuel pump’s air ﬁlter Ignition system Check the safety system Main fuse Replacing the light bulbs Fitting the cutting head When the engine is running. Mind your ﬁngersChecking the tyre pressure Checking the engine’s cooling air intake Trapping your hand Removing the cutting unit Adjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belts Placing in the service position Service position for the cutting unit Restoring from service position Checking the bladesRemoving the BioClip plug Replacing the engine oil LubricationChecking the engine’s oil level Changing the oil ﬁlter Lubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Problem Procedure Troubleshooting schedule Guard ServiceStorage Winter storage Technical data EC-declaration of conformity Applies to Europe only Page ´z+S!r¶6H¨ Page 1151018-26 ´z+S!r¶6H¨ ´z+S!r¶6H¨