Husqvarna 1153177-26 manual Tree felling technique, Safe distance, Felling direction

Page 25

WORKING TECHNIQUES

Tree felling technique

IMPORTANT! It takes a lot of experience to fell a tree. Inexperienced users of chain saws should not fell trees. Do not attempt any task that you feel unsure of!

Safe distance

The safe distance between a tree that is to be felled and anyone else working nearby is at least 2 1/2 tree lengths. Make sure that no-one else is in this ”risk zone” before or during felling.

Felling direction

The aim is to fell the tree in a position where you can limb and cross-cut the log as easily as possible. You want it to fall in a location where you can stand and move about safely.

Once you have decided which way you want the tree to fall you must judge which way the tree would fall naturally.

Several factors affect this:

•Lean of the tree

•Bend

•Wind direction

•Arrangement of branches

•Weight of snow

•Obstacles within the reach of the tree: for example, other trees, power lines, roads and buildings.

•Look for signs of damage and rot in the stem, this makes it more probably that the tree will break and start to fall before you expect it to.

You may find you are forced to let the tree fall in its natural direction because it is impossible or dangerous to try to make it fall in the direction you first intended.

Another very important factor, which does not affect the felling direction but does affect your safety, is to make sure the tree has no damaged or dead branches that might break off and hit you during felling.

The main point to avoid is letting the tree fall onto another tree. It is very dangerous to remove a trapped tree and

there is high accident risk. See instructions under the heading Freeing a tree that has fallen badly.

IMPORTANT! During critical felling operations, hearing protectors should be lifted immediately when sawing is completed so that sounds and warning signals can be heard.

Clearing the trunk and preparing your retreat

Delimb the stem up to shoulder height. It is safer to work from the top down and to have the tree between you and the saw.

Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall. Your path of retreat should be roughly 135 degrees away from the intended felling direction.

1

3

2

1

1

2

1Danger zone

2Retreat path

3Felling direction

English – 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 395XP, 395XPG Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufflerCutting equipment designed to reduce kickback General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening instructions considerably Increases the risk of kickbackAdjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Too largeWhich could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment OperatorFitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsJam. Always stop the engine before cleaning Not safely controlled with one hand Basic cutting techniqueHandles with both hands GeneralLimbing Procedures drastically increase the riskLogs are lying together. Such Or fatal injurySafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Directional cutsWhat is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburettor adjustment MaintenanceCarburettor with movement limiters Carburettor without movement limiters Recommended engine speeds are as follows Checking the front hand guard Checking brake band wearImmediately Checking the inertia brake releaseMuffler Tensioning the recoil spring Changing a broken or worn starter cordChanging a broken recoil spring Spark plug Air filterLubricating the bar tip sprocket Fitting the starterAir Injection centrifugal cleaning Adjustment of the oil pumpNeedle bearing lubrication Cooling systemHeated handles Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 122005, EN ISO Page Original instructions 1153177-26
Top Page Image Contents