Husqvarna 1153177-26 manual Maintenance schedule

Page 39

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section.

Daily maintenance

Weekly maintenance

Monthly maintenance

 

 

 

 

On chain saws without a catalytic

Check the brake band on the chain

 

brake for wear. Replace when less

Clean the outside of the machine.

converter, check the cooling system

than 0.6 mm (0,024 inch) remains at

 

weekly.

 

the most worn point.

 

 

 

 

 

Check that the components of the

Check the starter, starter cord and

Check the clutch centre, clutch drum

throttle control work safely. (Throttle

return spring.

and clutch spring for wear.

lockout and throttle control.)

 

 

 

 

 

Clean the chain brake and check that

 

 

it operates safely. Make sure that the

Check that the vibration damping

Clean the spark plug. Check that the

chain catcher is undamaged, and

elements are not damaged.

electrode gap is 0.5 mm.

replace it if necessary.

 

 

 

 

 

The bar should be turned daily for

 

 

more even wear. Check the

 

 

lubrication hole in the bar, to be sure it

Lubricate the clutch drum bearing.

Clean the outside of the carburettor.

is not clogged. Clean the bar groove.

 

 

If the bar has a sprocket tip, this

 

 

should be lubricated.

 

 

 

 

 

Check that the bar and chain are

File off any burrs from the edges of

Check the fuel filter and the fuel hose.

getting sufficient oil.

the bar.

Replace if necessary.

 

 

 

Check the saw chain with regard to

 

 

visible cracks in the rivets and links,

 

 

whether the saw chain is stiff or

Clean or replace the spark arrestor

Empty the fuel tank and clean the

whether the rivets and links are

mesh on the muffler.

inside.

abnormally worn. Replace if

 

 

necessary.

 

 

 

 

 

Sharpen the chain and check its

 

 

tension and condition. Check the drive

Clean the carburettor compartment.

Empty the oil tank and clean the

sprocket for excessive wear and

inside.

 

replace if necessary.

 

 

 

 

 

Clean the starter units air intake.

Clean the air filter. Replace if

Check all cables and connections.

necessary.

 

 

 

 

 

Check that nuts and screws are tight.

 

 

 

 

 

Check that the stop switch works

 

 

correctly.

 

 

 

 

 

Check that there are no fuel leaks

 

 

from the engine, tank or fuel lines.

 

 

 

 

 

On chain saws with a catalytic

 

 

converter, check the cooling system

 

 

daily.

 

 

 

 

 

English – 39

Image 39
Contents 395XP, 395XPG KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Muffler Stop switchCutting equipment Vibration damping systemCutting equipment designed to reduce kickback Increases the risk of kickback Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Sharpening instructions considerablyToo large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainChecking chain lubrication Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Filling with chain oilOperator Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentWorking with the chain AssemblyFitting the bar and chain Fitting a spike bumperFuel Fuel HandlingLong-term storage Fuel safetyFuelling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useJam. Always stop the engine before cleaning General Basic cutting techniqueNot safely controlled with one hand Handles with both handsOr fatal injury Procedures drastically increase the riskLimbing Logs are lying together. SuchClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsHow to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburettor adjustmentCarburettor with movement limiters Carburettor without movement limiters Recommended engine speeds are as follows Checking the front hand guard Checking brake band wearImmediately Checking the inertia brake releaseMuffler Changing a broken or worn starter cord Tensioning the recoil springChanging a broken recoil spring Fitting the starter Air filterSpark plug Lubricating the bar tip sprocketCooling system Adjustment of the oil pumpAir Injection centrifugal cleaning Needle bearing lubricationHeated handles Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 122005, EN ISO Page Original instructions 1153177-26