Husqvarna 1153177-26 manual Recommended engine speeds are as follows

Page 31

MAINTENANCE

•The carburettor has three adjustment controls:

-L = Low speed jet

-H = High speed jet

-T = Idle adjustment screw

•The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic settings and running in

The basic carburettor settings are adjusted during testing at the factory. The basic settings are H = 1 turn and L = 1 turn. To provide the engine’s components with good initial lubrication (during running in) the carburettor should be set for a richer fuel mixture for the first 3-4 hours that the chain saw is in use. To do this, adjust the fast idle speed to 600-700 rpm below the recommended maximum fast idle speed.

If you are unable to check the fast idle speed using a tachometer the H-jet should not be set for a leaner mixture than given in the basic settings. The recommended maximum fast idle speed must not be exceeded.

CAUTION! If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops.

Fine adjustment

When the machine has been ”run-in” the carburettor should be finely adjusted. The fine adjustment should be carried out by a qualified person. First adjust the L-jet, then the idling screw T and then the H-jet.

The recommended engine speeds are as follows:

Conditions

•Before any adjustments are made the air filter should be clean and the cylinder cover fitted. Adjusting the carburettor while a dirty air filter is in use will result in a leaner mixture next time the filter is cleaned. This can give rise to serious engine damage.

•Carefully turn the L and H-jets clockwise as far as they will go. Now turn the jets one turn anti-clockwise. The carburettor is now set to H = 1 and L = 1.

•Now start the machine according to the starting instructions and let it warm up for 10 minutes.

CAUTION! If the chain rotates while idling the T- screw must be turned anti-clockwise until the chain stops.

•Place the machine on a flat surface so that the bar points away from you and so that the bar and chain do not come into contact with the surface or other objects.

Low speed jet L

Try to find the highest idle speed by turning the low speed jet L clockwise then anti-clockwise. When the highest speed has been found, turn the low speed jet L 1/4 turn anti-clockwise.

+ 1/4

L

CAUTION! If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops.

Fine adjustment of the idle speed T

Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate.

!

WARNING! Contact your servicing

dealer, if the idle speed setting cannot be

 

adjusted so that the chain stops. Do not

 

use the chain saw until it has been

 

properly adjusted or repaired.

High speed jet H

•The high speed jet H influences the power and engine speed of the machine. If the high speed jet is set too rich (H-jet screwed in too far) the machine will over-rev and this will damage the engine. Run the machine at full throttle for about 10 seconds. Then turn the H-jet 1/4 turn anti-clockwise. Run the machine at full throttle for another 10 seconds or so and listen to the difference in the fast idle speed. Repeat this

English – 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents 395XP, 395XPG Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Muffler Stop switchCutting equipment Vibration damping systemCutting equipment designed to reduce kickback Increases the risk of kickback Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Sharpening instructions considerablyToo large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainChecking chain lubrication Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Filling with chain oilOperator Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentWorking with the chain AssemblyFitting the bar and chain Fitting a spike bumperFuel Fuel HandlingLong-term storage Fuel safetyFuelling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useJam. Always stop the engine before cleaning General Basic cutting techniqueNot safely controlled with one hand Handles with both handsOr fatal injury Procedures drastically increase the riskLimbing Logs are lying together. SuchClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsWhat is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburettor adjustment MaintenanceCarburettor with movement limiters Carburettor without movement limiters Recommended engine speeds are as follows Checking the front hand guard Checking brake band wearImmediately Checking the inertia brake releaseMuffler Tensioning the recoil spring Changing a broken or worn starter cordChanging a broken recoil spring Fitting the starter Air filterSpark plug Lubricating the bar tip sprocketCooling system Adjustment of the oil pumpAir Injection centrifugal cleaning Needle bearing lubricationHeated handles Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 122005, EN ISO Page Original instructions 1153177-26
Top Page Image Contents