Husqvarna 1153177-26 manual EC-declaration of conformity, Applies to Europe only

Page 42

TECHNICAL DATA

EC-declaration of conformity

(Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the chain saw Husqvarna 395XP/XPG from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), is in conformity with the requirements of the COUNCIL’S DIRECTIVES:

-of May 17, 2006 "relating to machinery" 2006/42/EC

-of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.

-of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

For information relating to noise emissions, see the chapter Technical data. The following standards have been applied:

EN ISO 12100-2:2003, CISPR 12:2005, EN ISO 11681-1:2004

Notiﬁed body: 0363, Deutsche Prüfstelle für Land- und Forsttechnik, Weissensteinstr 70/72, DE-34131 Kassel, Germany, has carried out EC type examination in accordance with the machinery directive’s (2006/42/EC) article 12, point 3b. The certiﬁcates for EC type examination in accordance with annex IX, have the numbers: K-EG-2009/2980.

In addition, SMP, Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has certiﬁed conformity with annex V of the Council’s Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The certiﬁcate has the number: 01/161/019.

The supplied chain saw conforms to the example that underwent EC type examination.

Huskvarna December 29, 2009

Bengt Frögelius, Development director chainsaw R (Authorized representative for Husqvarna AB and responsible for technical documentation.)

´®z+U1h¶6d¨

´®z+U1h¶6d¨

42 – English

Image 42

Contents 395XP, 395XPG KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufﬂerCutting equipment designed to reduce kickback Sharpening instructions considerably Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Increases the risk of kickbackTensioning the chain General advice on adjusting depth gauge settingAdjustment of depth gauge setting Too largeFilling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication OperatorFitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before cleaning Handles with both hands Basic cutting techniqueNot safely controlled with one hand GeneralLogs are lying together. Such Procedures drastically increase the riskLimbing Or fatal injuryFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutHow to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburettor adjustmentCarburettor with movement limiters Carburettor without movement limiters Recommended engine speeds are as follows Checking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMufﬂer Changing a broken or worn starter cord Tensioning the recoil springChanging a broken recoil spring Lubricating the bar tip sprocket Air ﬁlterSpark plug Fitting the starterNeedle bearing lubrication Adjustment of the oil pumpAir Injection centrifugal cleaning Cooling systemWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain ﬁling and ﬁle gaugesEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 122005, EN ISO Page Original instructions 1153177-26