Husqvarna 1153177-26 manual General Safety Precautions, Before using a new chain saw

Page 6

GENERAL SAFETY PRECAUTIONS

Before using a new chain saw

Please read this manual carefully.

Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly.

Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping.

Do not use the chain saw until sufficient chain oil has reached the chain. See instructions under the heading Lubricating cutting equipment.

Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection.

!

WARNING! Under no circumstances may

the design of the machine be modified

 

without the permission of the

 

manufacturer. Always use genuine

 

accessories. Non-authorized

 

modifications and/or accessories can

 

result in serious personal injury or the

 

death of the operator or others.

WARNING! A chain saw is a dangerous ! tool if used carelessly or incorrectly and

can cause serious, even fatal injuries. It is very important that you read and understand the contents of this operator’s manual.

WARNING! The inside of the muffler ! contain chemicals that may be

carcinogenic. Avoid contact with these elements in the event of a damaged muffler.

WARNING! Long term inhalation of the ! engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a

health risk.

WARNING! This machine produces an ! electromagnetic field during operation.

This field may under some circumstances interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this machine.

WARNING! Never allow children to use or ! be in the vicinity of the machine. As the

machine is equipped with a spring- loaded stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the machine. This can mean a risk of serious personal injury. Therefore remove the spark plug cap when the machine is not under close supervision.

Important

IMPORTANT!

The machine is only designed for cutting wood.

You should only use the saw with the bar and chain combinations we recommend in the chapter Technical data.

Never use the machine if you are fatigued, while under the influence of alcohol or drugs, medication or anything that could affect your vision, alertness, coordination or judgement.

Wear personal protective equipment. See instructions under the heading ”Personal protective equipment”.

Do not modify this product or use it if it appears to have been modified by others.

Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions under the heading Maintenance.

Never use any accessories other than those recommended in this manual. See instructions under the headings Cutting equipment and Technical data.

NB! Always wear protective glasses or a face visor to reduce the risk of injury from thrown objects. A chain saw is capable of throwing objects, such as wood chips, small pieces of wood, etc, at great force. This can result in serious injury, especially to the eyes.

WARNING! Running an engine in a ! confined or badly ventilated area can

result in death due to asphyxiation or carbon monoxide poisoning.

WARNING! Faulty cutting equipment or ! the wrong combination of bar and saw

chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

6 – English

Image 6
Contents 395XP, 395XPG KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback Sharpening instructions considerably Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Increases the risk of kickbackTensioning the chain General advice on adjusting depth gauge settingAdjustment of depth gauge setting Too largeFilling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication OperatorFitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before cleaning Handles with both hands Basic cutting techniqueNot safely controlled with one hand GeneralLogs are lying together. Such Procedures drastically increase the riskLimbing Or fatal injuryFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutHow to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburettor adjustmentCarburettor with movement limiters Carburettor without movement limiters Recommended engine speeds are as follows Checking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Changing a broken or worn starter cord Tensioning the recoil springChanging a broken recoil spring Lubricating the bar tip sprocket Air filterSpark plug Fitting the starterNeedle bearing lubrication Adjustment of the oil pumpAir Injection centrifugal cleaning Cooling systemWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 122005, EN ISO Page Original instructions 1153177-26