Husqvarna 1153177-26 manual Needle bearing lubrication, Adjustment of the oil pump, Cooling system

Page 37

MAINTENANCE

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week). NB! Use a high-quality bearing grease or engine oil. See instructions under the heading Cutting equipment.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory set to 1 turn open. Turning the screw clockwise will reduce the oil ﬂow and turning the screw anti-clockwise will increase the oil ﬂow.

Recommended settings:

Bar 18"-20": 0 turns from the closed position.

Bar 20"-24": 3/4 turns from the closed position.

Bar 24"-28": 1 1/2 turns from the closed position.

Bar 28" and longer: 1 3/4 turns from the closed position.

These recommendations apply to Husqvarna’s chain oil, for other chain oils increase the oil ﬂow by one step.

!	WARNING! The engine must not be
	running when making adjustments.

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2Air guide plate.

3Fins on the ﬂywheel.

4Cooling ﬁns on the cylinder.

5Cylinder cover (directs cold air over the cylinder).

5

4

3

2

1

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

”Air Injection” centrifugal cleaning

Centrifugal cleaning means the following: All air to the carburettor passes through the starter. Dirt and dust is centrifuged out by the cooling fan.

IMPORTANT! In order to maintain operation of the centrifugal cleaning system it must be regularly maintained. Clean the air intake to the starter, the ﬁns on the ﬂywheel, the space around the ﬂywheel, inlet pipe and carburettor compartment.

English – 37

Image 37

Contents 395XP, 395XPG Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufﬂerCutting equipment designed to reduce kickback General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening instructions considerably Increases the risk of kickbackAdjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Too largeWhich could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment OperatorFitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsJam. Always stop the engine before cleaning Not safely controlled with one hand Basic cutting techniqueHandles with both hands GeneralLimbing Procedures drastically increase the riskLogs are lying together. Such Or fatal injurySafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Directional cutsWhat is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburettor adjustment MaintenanceCarburettor with movement limiters Carburettor without movement limiters Recommended engine speeds are as follows Checking the front hand guard Checking brake band wearImmediately Checking the inertia brake releaseMufﬂer Tensioning the recoil spring Changing a broken or worn starter cordChanging a broken recoil spring Spark plug Air ﬁlterLubricating the bar tip sprocket Fitting the starterAir Injection centrifugal cleaning Adjustment of the oil pumpNeedle bearing lubrication Cooling systemHeated handles Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain ﬁling and ﬁle gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 122005, EN ISO Page Original instructions 1153177-26