Husqvarna 1153137-95 manual General advice on adjusting depth gauge setting, Too large

Page 13

GENERAL SAFETY PRECAUTIONS

•The cutting part of the chain is called the cutter and consists of a cutting tooth (A) and the depth gauge

(B). The cutters cutting depth is determined by the difference in height between the two (depth gauge setting).

When you sharpen a cutting tooth there are four important factors to remember.

1 Filing angle

2Cutting angle

3File position

4Round file diameter

It is very difficult to sharpen a chain correctly without the right equipment. We recommend that you use our file gauge. This will help you obtain the maximum kickback reduction and cutting performance from your chain.

See instructions under the heading Technical data for information about sharpening your chain.

WARNING! Departure from the

! sharpening instructions considerably

increases the risk of kickback.

Sharpening cutting teeth

To sharpen cutting teeth you will need a round file and a file gauge. See instructions under the heading Technical

1153137-95 Rev.2 2009-12-29

data for information on the size of file and gauge that are recommended for the chain fitted to your chain saw.

•Check that the chain is correctly tensioned. A slack chain will move sideways, making it more difficult to sharpen correctly.

•Always file cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on one side first, then turn the chain saw and file the teeth on the other side.

•File all the teeth to the same length. When the length of the cutting teeth is reduced to 5/32 inch (4 mm) the chain is worn out and should be replaced.

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

 

!

WARNING! The risk of kickback is

 

increased if the depth gauge setting is

 

 

too large!

 

 

 

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents
455e Rancher Rancher 460 Rancher Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingBar ChainIncreased if the depth gauge setting is General advice on adjusting depth gauge settingAdjustment of depth gauge setting Too largeBar and cause serious or even fatal injury Tensioning the chainRancher, 460 Rancher 455e RancherFilling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyRancher, 460 Rancher 455e RancherAssembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Tree felling techniqueLog is supported at one end. There is a high risk Safe distanceClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut Freeing a tree that has fallen badlyFreeing a trapped tree What is kickback? How to avoid kickbackGeneral advice Cutting trees and branches that are in tensionCutting the trunk into logs Carburetor adjustment MaintenanceGeneral When the bar hits the stump the brake should be applied Correctly adjusted carburetorChecking brake band wear Checking the front hand guardChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterSpark plug Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C 32F or colder Air Injection centrifugal cleaningTemperature -5C 23F or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataGauge, Saw chain designation Saw chain filing and file gaugesYour Warranty Rights and Obligations Federal Emission Control Warranty StatementMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Safety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions1153137-95