Husqvarna 1153137-95 Air filter, Tensioning the recoil spring, Changing a broken recoil spring

Page 35

MAINTENANCE

recoil spring by letting the pulley rotate slowly backwards.

1 2

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley. Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the center of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned an additional 1/2 turn when the starter cord is pulled all the way out.

1

2

Changing a broken recoil spring

•Lift off the pulley. See instructions under heading Changing a broken or worn starter cord.

•Remove the recoil spring from inside the pulley by tapping the pulley lightly with its inside face downwards against a work bench or the like. If the spring pops out during fitting, wind it up again, working from the outside in towards centre.

•Lubricate the recoil spring with light oil. Fit the pulley and tension the recoil spring.

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice.

1153137-95 Rev.2 2009-12-29

English – 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 455e Rancher Rancher 460 Rancher Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerChain Sharpening your chain and adjusting depth gauge settingCutting equipment designed to reduce kickback BarToo large General advice on adjusting depth gauge settingIncreased if the depth gauge setting is Adjustment of depth gauge setting455e Rancher Tensioning the chainBar and cause serious or even fatal injury Rancher, 460 RancherChecking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication 455e Rancher AssemblyFitting the bar and chain Rancher, 460 RancherAssembly Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueSafe distance Tree felling techniqueLimbing Log is supported at one end. There is a high riskDirectional cuts Felling directionClearing the trunk and preparing your retreat Freeing a trapped tree Freeing a tree that has fallen badlyFelling cut Cutting trees and branches that are in tension How to avoid kickbackWhat is kickback? General adviceCutting the trunk into logs General MaintenanceCarburetor adjustment Checking the front hand guard Correctly adjusted carburetorWhen the bar hits the stump the brake should be applied Checking brake band wearChecking the brake trigger Changing a broken or worn starter cord MufflerStarter Fitting the starter Air filterTensioning the recoil spring Changing a broken recoil springNeedle bearing lubrication Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Temperature -5C 23F or colderDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataGauge, Saw chain designation Saw chain filing and file gaugesYour Warranty Rights and Obligations Federal Emission Control Warranty StatementMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions1153137-95

1153137-95 specifications

The Husqvarna 1153137-95 is an essential addition to any serious gardener's toolkit, renowned for its remarkable efficiency and innovative design. This advanced garden trimmer is engineered to provide optimal performance, durability, and ease of use, making it perfect for both professional landscapers and home gardening enthusiasts.

One of the standout features of the Husqvarna 1153137-95 is its robust motor. With a powerful engine, this trimmer delivers impressive torque and cutting speed, enabling users to tackle even the toughest grass and weeds with ease. The lightweight construction ensures that operators can handle the unit comfortably during extended use without experiencing fatigue.

The trimmer is designed with advanced technology, including an automatic line feed system. This feature ensures that the cutting line extends automatically when needed, minimizing downtime and allowing users to focus on their trimming tasks without interruption. Additionally, the Husqvarna 1153137-95 boasts an ergonomic design, incorporating adjustable handles and a well-balanced structure that enhances maneuverability and precision during operation.

Another significant characteristic of the Husqvarna 1153137-95 is its cutting path, which is optimally sized to provide efficient coverage without compromising on control. With durable cutting attachments, this trimmer can easily switch between different heads depending on the specific gardening needs, making it a versatile tool capable of edging, trimming, and shaping your garden effortlessly.

The safety features incorporated into the Husqvarna 1153137-95 are noteworthy. The trimmer comes equipped with a protective guard that shields users from debris, while a safety throttle provides additional peace of mind by ensuring the trimmer only operates when desired.

Lastly, the Husqvarna brand is well-regarded for its commitment to sustainability, and the 1153137-95 reflects this ethos, as it is engineered to reduce emissions and improve fuel efficiency. This trimmer represents a blend of cutting-edge technology and practicality, making it an invaluable tool for any gardening project.

In conclusion, the Husqvarna 1153137-95 is a well-rounded garden trimmer that combines power, efficiency, and user-friendly features. Its advanced technologies and safety elements make it a trusted choice for anyone looking to achieve a well-maintained landscape with minimal effort.
Top Page Image Contents