Husqvarna 1153137-95 manual Correctly adjusted carburetor, Checking brake band wear

Page 32

MAINTENANCE

CAUTION! If the high speed jet is screwed in too far, it may damage the piston/cylinder.

When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance.

The carburetor’s high speed jet is then locked using a limiter cap in the fully screwed out position.The limiter cap limits the potential to adjust the high speed jet to at most half a turn.

To adjust the carburetor correctly you should contact a mechanic with access to a rev counter.

CAUTION! As the spark is cut off, the rev counter does not show speeds higher than 13600 rpm.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine accelerates without hesitation and the machine 4-cycles a little at max. speed. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H- jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine.

Checking, maintaining and servicing chain saw safety equipment

Note! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below we recommend you to contact our servicing dealer.

Chain brake and front hand guard

Checking brake band wear

Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake.

Regularly check that the brake band is at least 0.024 inch (0.6 mm) thick at its thinnest point.

Checking the front hand guard

Make sure the front hand guard is not damaged and that there are no visible defects such as cracks.

Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover.

Checking the inertia brake release

With the engine turned off, hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle.

When the bar hits the stump the brake should be applied.

32 – English

1153137-95 Rev.2 2009-12-29

Page 31 Page 33
Image 32
Page 31 Page 33
Contents 455e Rancher Rancher 460 Rancher Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackBar ChainGeneral advice on adjusting depth gauge setting Increased if the depth gauge setting isAdjustment of depth gauge setting Too largeTensioning the chain Bar and cause serious or even fatal injuryRancher, 460 Rancher 455e RancherChecking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Assembly Fitting the bar and chainRancher, 460 Rancher 455e RancherAssembly Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsTree felling technique LimbingLog is supported at one end. There is a high risk Safe distanceDirectional cuts Felling directionClearing the trunk and preparing your retreat Freeing a trapped tree Freeing a tree that has fallen badlyFelling cut How to avoid kickback What is kickback?General advice Cutting trees and branches that are in tensionCutting the trunk into logs General MaintenanceCarburetor adjustment Correctly adjusted carburetor When the bar hits the stump the brake should be appliedChecking brake band wear Checking the front hand guardChecking the brake trigger Changing a broken or worn starter cord MufflerStarter Air filter Tensioning the recoil springChanging a broken recoil spring Fitting the starterAdjustment of the oil pump Spark plugLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderTemperature -5C 23F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges Gauge, Saw chain designationFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts American Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions1153137-95

1153137-95 specifications

The Husqvarna 1153137-95 is an essential addition to any serious gardener's toolkit, renowned for its remarkable efficiency and innovative design. This advanced garden trimmer is engineered to provide optimal performance, durability, and ease of use, making it perfect for both professional landscapers and home gardening enthusiasts.

One of the standout features of the Husqvarna 1153137-95 is its robust motor. With a powerful engine, this trimmer delivers impressive torque and cutting speed, enabling users to tackle even the toughest grass and weeds with ease. The lightweight construction ensures that operators can handle the unit comfortably during extended use without experiencing fatigue.

The trimmer is designed with advanced technology, including an automatic line feed system. This feature ensures that the cutting line extends automatically when needed, minimizing downtime and allowing users to focus on their trimming tasks without interruption. Additionally, the Husqvarna 1153137-95 boasts an ergonomic design, incorporating adjustable handles and a well-balanced structure that enhances maneuverability and precision during operation.

Another significant characteristic of the Husqvarna 1153137-95 is its cutting path, which is optimally sized to provide efficient coverage without compromising on control. With durable cutting attachments, this trimmer can easily switch between different heads depending on the specific gardening needs, making it a versatile tool capable of edging, trimming, and shaping your garden effortlessly.

The safety features incorporated into the Husqvarna 1153137-95 are noteworthy. The trimmer comes equipped with a protective guard that shields users from debris, while a safety throttle provides additional peace of mind by ensuring the trimmer only operates when desired.

Lastly, the Husqvarna brand is well-regarded for its commitment to sustainability, and the 1153137-95 reflects this ethos, as it is engineered to reduce emissions and improve fuel efficiency. This trimmer represents a blend of cutting-edge technology and practicality, making it an invaluable tool for any gardening project.

In conclusion, the Husqvarna 1153137-95 is a well-rounded garden trimmer that combines power, efficiency, and user-friendly features. Its advanced technologies and safety elements make it a trusted choice for anyone looking to achieve a well-maintained landscape with minimal effort.
Top Page Image Contents