Husqvarna 1153137-95 manual Basic cutting technique, Terms

Page 25

WORKING TECHNIQUES

user. If the saw chain is jamming, the saw may be pushed back at you.

8Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which can lead to a kickback.

Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting with a pulling chain. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. Cutting with a pulling chain gives the operator better control over the chain saw and the position of the kickback zone.

9Follow the instructions on sharpening and maintaining your bar and chain. When you replace the bar and chain use only combinations that are recommended by us. See instructions under the headings Cutting equipment and Technical data.

Basic cutting technique

WARNING! Never use a chain saw by

! holding it with one hand. A chain saw is not safely controlled with one hand. Always have a secure, firm grip around the handles with both hands.

General

Always use full throttle when cutting!

Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load, i.e. without any resistance from the chain during cutting, can lead to serious engine damage).

Cutting from above = Cutting with a pulling chain.

Cutting from below = Cutting with pushing chain.

Cutting with a pushing chain increases the risk of kickback. See instructions under the heading How to avoid kickback.

1153137-95 Rev.2 2009-12-29

Terms

Cutting = General term for cutting through wood. Limbing = Cutting branches off a felled tree.

Splitting = When the object you are cutting breaks off before the cut is complete.

There are five important factors you should consider before making a cut:

1Make sure the cutting equipment will not jam in the cut.

2Make sure the object you are cutting will not split.

3Make sure the chain will not strike the ground or any other object during or after cutting.

4Is there a risk of kickback?

5Do the conditions and surrounding terrain affect how safely you can stand and move about?

Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension.

In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom.You need to support the object so that it will not trap the chain or split during cutting.

IMPORTANT! If the chain jams in the cut: stop the engine! Don’t try to pull the chain saw free. If you do you may be injured by the chain when the chain saw suddenly breaks free. Use a lever to open up the cut and free the chain saw.

The following instructions describe how to handle the common situations you are likely to encounter when using a chain saw.

English 25

Image 25
Contents 455e Rancher Rancher 460 Rancher Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingBar ChainIncreased if the depth gauge setting is General advice on adjusting depth gauge settingAdjustment of depth gauge setting Too largeBar and cause serious or even fatal injury Tensioning the chainRancher, 460 Rancher 455e RancherFilling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyRancher, 460 Rancher 455e RancherAssembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Tree felling techniqueLog is supported at one end. There is a high risk Safe distanceClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut Freeing a tree that has fallen badlyFreeing a trapped tree What is kickback? How to avoid kickbackGeneral advice Cutting trees and branches that are in tensionCutting the trunk into logs Carburetor adjustment MaintenanceGeneral When the bar hits the stump the brake should be applied Correctly adjusted carburetorChecking brake band wear Checking the front hand guardChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterSpark plug Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C 32F or colder Air Injection centrifugal cleaningTemperature -5C 23F or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataGauge, Saw chain designation Saw chain filing and file gaugesYour Warranty Rights and Obligations Federal Emission Control Warranty StatementMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Safety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions1153137-95

1153137-95 specifications

The Husqvarna 1153137-95 is an essential addition to any serious gardener's toolkit, renowned for its remarkable efficiency and innovative design. This advanced garden trimmer is engineered to provide optimal performance, durability, and ease of use, making it perfect for both professional landscapers and home gardening enthusiasts.

One of the standout features of the Husqvarna 1153137-95 is its robust motor. With a powerful engine, this trimmer delivers impressive torque and cutting speed, enabling users to tackle even the toughest grass and weeds with ease. The lightweight construction ensures that operators can handle the unit comfortably during extended use without experiencing fatigue.

The trimmer is designed with advanced technology, including an automatic line feed system. This feature ensures that the cutting line extends automatically when needed, minimizing downtime and allowing users to focus on their trimming tasks without interruption. Additionally, the Husqvarna 1153137-95 boasts an ergonomic design, incorporating adjustable handles and a well-balanced structure that enhances maneuverability and precision during operation.

Another significant characteristic of the Husqvarna 1153137-95 is its cutting path, which is optimally sized to provide efficient coverage without compromising on control. With durable cutting attachments, this trimmer can easily switch between different heads depending on the specific gardening needs, making it a versatile tool capable of edging, trimming, and shaping your garden effortlessly.

The safety features incorporated into the Husqvarna 1153137-95 are noteworthy. The trimmer comes equipped with a protective guard that shields users from debris, while a safety throttle provides additional peace of mind by ensuring the trimmer only operates when desired.

Lastly, the Husqvarna brand is well-regarded for its commitment to sustainability, and the 1153137-95 reflects this ethos, as it is engineered to reduce emissions and improve fuel efficiency. This trimmer represents a blend of cutting-edge technology and practicality, making it an invaluable tool for any gardening project.

In conclusion, the Husqvarna 1153137-95 is a well-rounded garden trimmer that combines power, efficiency, and user-friendly features. Its advanced technologies and safety elements make it a trusted choice for anyone looking to achieve a well-maintained landscape with minimal effort.