Husqvarna 1151338-95 manual Tensioning the chain

Page 14

GENERAL SAFETY PRECAUTIONS

•File all the teeth to the same length. When the length of the cutting teeth is reduced to 0.16 inch (4 mm) the chain is worn out and should be replaced.

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

 

!

WARNING! The risk of kickback is

 

increased if the depth gauge setting is

 

 

 

 

too large!

 

 

 

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off

! the bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

14 – English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 395XP Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawEPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping system Stop switch Cutting equipment MufflerChain Cutting equipment designed to reduce kickbackBar Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Working with the chain AssemblyFitting the bar and chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsTree felling technique Directional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs Maintenance Carburetor adjustmentHigh speed jet H Fine adjustment of the idling speed TCorrectly adjusted carburetor Checking the inertia brake release ImmediatelyMuffler Changing a broken recoil spring Changing a broken or worn starter cordTensioning the recoil spring Lubricating the bar tip sprocket Air filterSpark plug Fitting the starterWhen making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Needle bearing lubricationWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Saw chain filing and file gauges050/1,3 mm 063/1,6 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw Kickback safety precautionsPage 1151338-95
Top Page Image Contents