Husqvarna 1151338-95 manual Maintenance, Carburetor adjustment

Page 30

MAINTENANCE

Carburetor adjustment

Due to existing environmental and emissions legislation your chain saw is equipped with movement limiters on the carburetor adjuster screws. These limit the adjustment possibilities to a maximum of a 1/2 turn.

1/2

1/2

Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions.

Function, Basic settings, Fine adjustment

WARNING! Do not start the chain saw

! unless the bar, chain and clutch cover (chain brake) are fitted, otherwise the clutch may come loose and cause personal injury.

Function

•The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. The air/fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine.

•The setting of the carburetor means that the engine is adapted to local conditions, for example, the climate, altitude, fuel and the type of 2-stroke oil.

•The carburetor has three adjustment controls:

-L = Low speed jet

-H = High speed jet

-T = Idle adjustment screw

•The L and H-jets are used to adjust the supply of fuel to match the rate that air is admitted, which is controlled with the throttle. If they are screwed clockwise the air/fuel ratio becomes leaner (less fuel) and if they are turned anti-clockwise the ratio becomes richer (more fuel). A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed.

•The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic settings and running in

The basic carburetor settings are adjusted during testing at the factory. Avoid running at a too high speed for extended periods during the first 10 hours.

CAUTION! If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops.

Rec. idle speed: 2500 rpm

WARNING! Contact your servicing

! dealer, if the idle speed setting cannot be adjusted so that the chain stops at idle. Do not use the chain saw until it has been properly adjusted or repaired.

Fine adjustment

When the machine has been ”run-in” the carburetor should be finely adjusted. The fine adjustment should be carried out by a qualified person. First adjust the L- jet, then the idling screw T and then the H-jet.

Conditions

•Before any adjustments are made the air filter should be clean and the cylinder cover fitted. Adjusting the carburetor while a dirty air filter is in use will result in a leaner mixture next time the filter is cleaned. This can give rise to serious engine damage.

•Do not attempt to adjust the L and H jets beyond either stop as this could cause damage.

•Now start the machine according to the starting instructions and let it warm up for 10 minutes.

CAUTION! If the chain rotates while idling the T- screw must be turned anti-clockwise until the chain stops.

•Place the machine on a flat surface so that the bar points away from you and so that the bar and chain do not come into contact with the surface or other objects.

Low speed jet L

Turn the low speed jet L clockwise until it stops. If the engine accelerates poorly or idles unevenly, turn the low speed jet L anticlockwise until good acceleration and idling are achieved.

CAUTION! If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents 395XP Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawEPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback BarChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Chain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainWorking with the chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsTree felling technique Felling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cut How to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentFine adjustment of the idling speed T Correctly adjusted carburetorHigh speed jet H Checking the inertia brake release ImmediatelyMuffler Changing a broken or worn starter cord Tensioning the recoil springChanging a broken recoil spring Lubricating the bar tip sprocket Air filterSpark plug Fitting the starterWhen making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Needle bearing lubricationWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Saw chain filing and file gauges050/1,3 mm 063/1,6 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw Kickback safety precautionsPage 1151338-95

1151338-95 specifications

The Husqvarna 1151338-95 is an innovative chainsaw that exemplifies the blend of power, performance, and user-friendly features, making it a popular choice among both amateur woodworkers and professional landscapers. Designed with a 14-inch cutting bar, this chainsaw is ideal for pruning, trimming, and cutting small to medium-sized trees, providing the versatility needed for various tasks.

One of the main features of the Husqvarna 1151338-95 is its powerful X-Torq engine. This engine is designed to deliver maximum power while minimizing fuel consumption and emissions, making it environmentally friendly. The X-Torq technology ensures that users experience less vibration while operating the chainsaw, reducing fatigue during prolonged use. This feature enhances overall comfort and allows for more precise control.

In addition to its eco-friendly engine, the Husqvarna 1151338-95 is equipped with Smart Start technology, which facilitates easy starting with minimal effort. The fuel pump and choke are designed to work in harmony, enabling the user to start the saw quickly, even in cold conditions. This is particularly beneficial for those who may find starting a traditional chainsaw challenging.

Safety is a top priority with the Husqvarna 1151338-95. It comes with a chain brake, which instantly stops the chain in the event of kickback, providing peace of mind to the user. The chainsaw also features a built-in low-vibration system that absorbs shocks and reduces overall vibration levels, allowing for safer and more comfortable operation.

Another notable characteristic of the Husqvarna 1151338-95 is its ergonomic design. The lightweight frame and well-placed handles provide excellent balance, making it easy to maneuver and operate for extended periods. The accessible air filter and easy-to-access oil tank also allow for convenient maintenance, ensuring that the chainsaw remains in optimal working condition.

The Husqvarna 1151338-95 is not just about raw power; it is a thoughtful combination of technology, comfort, and safety features, making it an excellent choice for anyone looking to tackle tasks around the home or in professional settings. With its advanced technologies and user-centric design, this chainsaw stands out as a reliable tool for cutting and pruning needs.
Top Page Image Contents