Husqvarna 1151338-95 manual Fuel Handling

Page 18

FUEL HANDLING

Fuel

Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

!

WARNING! Always ensure there is

adequate ventilation when handling fuel.

 

Gasoline

•Use good quality unleaded gasoline.

•CAUTION! Engines equipped with catalytic converters must be run on unleaded fuel mixtures.

•Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose. The green fuel cap on saws fitted with catalytic converters means that only unleaded gasoline can be used.

•The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

•When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor).

Running-in

Avoid running at a too high speed for extended periods during the first 10 hours.

Two-stroke oil

•For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines.

•Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

•Never use oil intended for four-stroke engines.

18 – English

Mixing ratio

1:50 (2%) for all engines.

Gasoline, litre

Two-stroke oil, litre

 

 

 

2% (1:50)

 

 

5

0,10

 

 

10

0,43/0,20

 

 

15

0,30

 

 

20

0,40

 

 

US gallon

US fl. oz.

 

 

1

2 1/2

 

 

2 1/2

6 1/2

 

 

5

12 7/8

 

 

Mixing

•Always mix the gasoline and oil in a clean container intended for fuel.

•Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

•Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

Chain oil

•We recommend the use of special oil (chain oil) with good adhesion characteristics.

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

•In temperatures below 32°F (0°C) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components.

•Contact your service agent when choosing chain oil.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 395XP Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawEPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback BarChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Chain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainWorking with the chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsTree felling technique Felling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cut How to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentFine adjustment of the idling speed T Correctly adjusted carburetorHigh speed jet H Checking the inertia brake release ImmediatelyMuffler Changing a broken or worn starter cord Tensioning the recoil springChanging a broken recoil spring Lubricating the bar tip sprocket Air filterSpark plug Fitting the starterWhen making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Needle bearing lubricationWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Saw chain filing and file gauges050/1,3 mm 063/1,6 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw Kickback safety precautionsPage 1151338-95

1151338-95 specifications

The Husqvarna 1151338-95 is an innovative chainsaw that exemplifies the blend of power, performance, and user-friendly features, making it a popular choice among both amateur woodworkers and professional landscapers. Designed with a 14-inch cutting bar, this chainsaw is ideal for pruning, trimming, and cutting small to medium-sized trees, providing the versatility needed for various tasks.

One of the main features of the Husqvarna 1151338-95 is its powerful X-Torq engine. This engine is designed to deliver maximum power while minimizing fuel consumption and emissions, making it environmentally friendly. The X-Torq technology ensures that users experience less vibration while operating the chainsaw, reducing fatigue during prolonged use. This feature enhances overall comfort and allows for more precise control.

In addition to its eco-friendly engine, the Husqvarna 1151338-95 is equipped with Smart Start technology, which facilitates easy starting with minimal effort. The fuel pump and choke are designed to work in harmony, enabling the user to start the saw quickly, even in cold conditions. This is particularly beneficial for those who may find starting a traditional chainsaw challenging.

Safety is a top priority with the Husqvarna 1151338-95. It comes with a chain brake, which instantly stops the chain in the event of kickback, providing peace of mind to the user. The chainsaw also features a built-in low-vibration system that absorbs shocks and reduces overall vibration levels, allowing for safer and more comfortable operation.

Another notable characteristic of the Husqvarna 1151338-95 is its ergonomic design. The lightweight frame and well-placed handles provide excellent balance, making it easy to maneuver and operate for extended periods. The accessible air filter and easy-to-access oil tank also allow for convenient maintenance, ensuring that the chainsaw remains in optimal working condition.

The Husqvarna 1151338-95 is not just about raw power; it is a thoughtful combination of technology, comfort, and safety features, making it an excellent choice for anyone looking to tackle tasks around the home or in professional settings. With its advanced technologies and user-centric design, this chainsaw stands out as a reliable tool for cutting and pruning needs.
Top Page Image Contents