Husqvarna 235F manual Fitting the trimmer guard and trimmer head Trimmy SII, Am L

Page 15

ASSEMBLY

CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

G

F

D

B

C

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D) and support flange (F) on the output shaft.

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

•When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade. You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area

where you should operate the socket spanner when loosening or tightening the nut.

Fitting the trimmer guard and trimmer head Trimmy SII

•Fit the correct trimmer guard (A) for use with the trimmer head. CAUTION! Ensure that the guard extension is fitted.

Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

H

L

M

BA

C

AM L

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Screw on the trimmer head (H) in the opposite direction to the direction of rotation.

H

•Tighten the trimmer head to a torque of 35-50 Nm (3.5-5 kpm).

•To dismantle, follow the instructions in the reverse order.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 235R 235FR Persons or animals come closer than KEY to SymbolsSymbols Operator of the machine must Ensure, while working, that noContents Dear Customer IntroductionWhat is what? What is WHAT?Personal protective equipment General Safety PrecautionsThrottle lockout Machine′s safety equipmentQuick release Stop switchCutting attachment guard Vibration damping systemLocking nut MufflerCutting equipment Cutting equipmentGeneral rules Sharpening the saw blade Sharpening grass cutters and grass blades Trimmer head Assembly Fitting the handlebarTransport position, handlebar Assembling the cutting equipment Fitting a blade guard, grass blade and grass cutterFitting the blade guard and saw blade AM L Fitting the trimmer guard and trimmer head Trimmy SIIAdjusting the harness and brush cutter Fitting other guards and cutting attachmentsSpreading the load on your shoulders Grass clearing Correct heightCorrect balance Forestry clearingFuel safety Fuel HandlingFuel Mixing FuellingCold engine Starting and StoppingCheck before starting Starting and stoppingStopping Warm engineStarting For throttle handles with a start throttle lockABC of clearing Basic safety rulesWorking Techniques General working instructionsControl the felling direction take advantage of the wind Forestry clearing using a saw blade Trimming Grass clearing using a grass bladeBrush cutting with a saw blade Grass trimming with a trimmer headSweeping CuttingCarburettor MaintenanceMuffler Cooling systemBevel gear Oiling the air filter Cleaning the air filterAir filter Spark plugMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataEC-declaration of conformity Applies to Europe only Page S35 2,7mm 095-.106 25 m 15 cm T35, T35x T45, T45x Auto Trimmy SII Page Page Page Page Original instructions 1153284-26
Top Page Image Contents