Ryobi Outdoor CS30 ZR30000 Assembly, See Figure, String Trimmer Shaft Coupler Guide Recess Button

Page 10
ASSEMBLY

ASSEMBLY

ATTACHING THE POWER HEAD TO THE ATTACHMENT

See Figure 2.

See Figure 2. WARNING:

Never attach or adjust any attachment while power head is running. Failure to stop the engine can cause serious personal injury.

The attachment connects to the power head by means of a coupler device.

1.Loosen the knob on the coupler of the power head shaft and remove the end cap from the attachment.

2.Push in the button located on the attachment shaft. Align the button with the guide recess on the power head coupler and slide the two shafts together. Rotate the attachment shaft until the button locks into the position- ing hole.

NOTE: If the button does not release completely in the positioning hole, the shafts are not locked into place. Slightly rotate from side to side until the button is locked into place.

3. Tighten the knob securely.

STRING TRIMMER WARNING:

Be certain the knob is fully tightened before operating equipment; check it periodically for tightness during use to avoid serious personal injury.

REMOVING THE ATTACHMENT FROM THE POWER HEAD

For removing or changing the attachment:

1.Loosen the knob.

2.Push in the button and twist the shafts to remove and separate ends.

ATTACHING THE STORAGE HANGER

See Figure 3.

There are two ways to hang your attachment for storage.

■To use the hanger cap, push in the button and place the hanger cap over end of the lower end attachment shaft. Slightly rotate the cap from side to side until the button locks into place.

■The secondary hole in the attachment shaft can be used for hanging purposes as well.

STRING TRIMMER

SHAFT

COUPLER

GUIDE

RECESS

BUTTON

POSITIONING

HOLE

KNOB

TRIMMER ATTACHMENT

Fig. 2

 

HANGER CAP

HOLE

SECONDARY

HOLE

BUTTON

Fig. 3

Page 10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents ZR30000 Series OPERATORS MANUAL30cc String Trimmers and Brushcutter SAVE THIS MANUAL FOR FUTURE REFERENCETABLE OF CONTENTS INTRODUCTIONGENERAL SAFETY RULES READ ALL INSTRUCTIONSSPECIFIC SAFETY RULES SPECIFIC SAFETY RULES FOR TRIMMER USENAME SYMBOLSSYMBOL EXPLANATIONSYMBOL SIGNAL SAVE THESE INSTRUCTIONSSERVICE MEANINGWeight - without fuel SPECIFICATIONSUNPACKING String cutting widthREAR HANDLE FEATURESHOUSING FRONT HANDLE KNOB CURVED SHAFT GRASS CHOKE LEVER COUPLER THROTTLE TRIGGER DRIVE SHAFTCOUPLER COUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSINGSTARTER GRIP THROTTLE TRIGGERSTRING TRIMMER SHAFT COUPLER GUIDE RECESS BUTTON ASSEMBLYSee Figure POSITIONING HOLE KNOBBOLT 1/4-20x 1 in. BOLT FRONT1/4-20 x 1 1/2 in FRONT HANDLE LOCK WASHER WING NUT BOLTFLAT WASHER HANDLE STRAP HANGER CLAMPBOLT BRACKET TO ATTACH THE CURVED SHAFT GRASS DEFLECTORZR30000 See Figure SLOT GEAR HEADREMOVING THE TRI-ARCBLADE AND BRUSHCUTTER GUARD GEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLYLATCH STRAP HANGER SHOULDER See Figures 10 andSLOT LOOSEN TIGHTEN INSTALLING THE TRI-ARCBLADE AND BRUSHCUTTER GUARDGEAR HEAD FLANGED WASHER SLOT CUPPED WASHER FUEL MIXTURE HIGH QUALITY 2-CYCLEENGINE OIL OPERATIONFUEL MIXTURE GASOLINECUTTING TIPS TO ADVANCE THE CUTTING LINETO ADVANCE THE CUTTING LINE MANUALLY See Figures 16 andTRI-ARCBLADE See Figures 19 andBLADE THRUST CUTTING TECHNIQUE - BLADESee Figures 21, 22, and IGNITION SWITCH THROTTLE TRIGGERPRIMER BULB STARTER GRIP IGNITION SWITCH STARTING TO STOP THE ENGINENEW PREWOUND SPOOL MAINTENANCETo install the spool retainer See Figures 24 andFIRST STRING See Figures 26, 27, andARROWS ON SPOOL ANCHOR HOLE FIRST STRING SLOT SECOND STRINGLATCH PULL COVER TO OPEN Cleaning InstructionsSee Figures 29 and FILTER SLOTS ON AIR FILTER BASE TABS ON AIRSPARK PLUG FUEL CAPSTORAGE 1 MONTH OR LONGER TROUBLESHOOTING IDLE SPEED SCREW OWNERSWARRANTY RESPONSIBILITIES WARRANTYMANUFACTURERS WARRANTY COVERAGE MAINTENANCE REQUIREMENTS5 Hours Emissions PartsEach Use AIR FILTER ASSYNOTES • HOW TO ORDER REPAIR PARTS RYOBI TECHNOLOGIES INC• SERVICE • MODEL NO. AND SERIAL NO
Top Page Image Contents