Ryobi Outdoor SS30 ZR30002 Operation, Fuel Mixture, FUEL MIXTURE HIGH QUALITY 2-CYCLEENGINE OIL

Page 15
OPERATION

OPERATION

FUELING AND REFUELING THE TRIMMER

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil. Pre-mix unleaded gasoline and 2-cycle engine oil in a clean 1 gallon container approved for gasoline.

Recommended fuel: This engine is certified to operate on unleaded gasoline intended for automotive use.

Mix a high quality 2-cycle engine oil at 2.6 oz. per gallon (US).

Do not use automotive oil or 2-cycle outboard oil.

DO NOT mix quantities larger than usable in a 30 day period.

FUEL MIXTURE

HIGH QUALITY 2-CYCLE ENGINE OIL

GASOLINE

OIL

 

1 gallon (US)

2.6 oz.

1 Liter

20 cc (20 ml)

FILLING TANK

1.Clean surface around fuel cap to prevent contamination.

2.Loosen fuel cap slowly. Rest the cap on a clean surface.

3.Carefully pour fuel into the tank. Avoid spillage.

4.Prior to replacing the fuel cap, clean and inspect the gasket.

5.Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage.

NOTE: It is normal for smoke to be emitted from a new engine after first use.

FUEL MIXTURE WARNING:

Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. (9 m) from refueling site before starting engine. Do not smoke!

OPERATING THE TRIMMER

See Figure 15.

GASOLINE WARNING:

Always position the unit on the operator's right side. The use of the unit on the operator's left side will expose the user to hot surfaces and can result in possible burn injury.

FILLING TANK WARNING:

To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level.

Hold the trimmer with the right hand on the rear handle and the left hand on the front handle. Keep a firm grip with both hands while in operation.Trimmer should be held at a comfortable position with the rear handle about hip height.

Always operate trimmer at full throttle. Cut tall grass from the top down.This will prevent grass from wrapping around the shaft housing and string head which may cause dam- age from overheating. If grass becomes wrapped around the string head, STOP THE ENGINE, disconnect the spark plug wire, and remove the grass. Prolonged cutting at partial throttle will result in oil dripping from the muffler.

OPERATING THE

CURVED SHAFT

TRIMMER

OPERATING THE

STRAIGHT SHAFT

TRIMMER

Fig. 15

Page

Page 14 Page 16
Image 15
Page 14 Page 16
Contents SAVE THIS MANUAL FOR FUTURE REFERENCE OPERATORS MANUAL30cc String Trimmers and Brushcutter ZR30000 SeriesINTRODUCTION TABLE OF CONTENTSREAD ALL INSTRUCTIONS GENERAL SAFETY RULESSPECIFIC SAFETY RULES FOR TRIMMER USE SPECIFIC SAFETY RULESEXPLANATION SYMBOLSSYMBOL NAMEMEANING SAVE THESE INSTRUCTIONSSERVICE SYMBOL SIGNALString cutting width SPECIFICATIONSUNPACKING Weight - without fuelCHOKE LEVER COUPLER THROTTLE TRIGGER DRIVE SHAFT FEATURESHOUSING FRONT HANDLE KNOB CURVED SHAFT GRASS REAR HANDLETHROTTLE TRIGGER COUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSINGSTARTER GRIP COUPLERPOSITIONING HOLE KNOB ASSEMBLYSee Figure STRING TRIMMER SHAFT COUPLER GUIDE RECESS BUTTONHANDLE STRAP HANGER CLAMP FRONT HANDLE LOCK WASHER WING NUT BOLTFLAT WASHER BOLT 1/4-20x 1 in. BOLT FRONT1/4-20 x 1 1/2 inSLOT GEAR HEAD TO ATTACH THE CURVED SHAFT GRASS DEFLECTORZR30000 See Figure BOLT BRACKETSee Figures 10 and GEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLYLATCH STRAP HANGER SHOULDER REMOVING THE TRI-ARCBLADE AND BRUSHCUTTER GUARDINSTALLING THE TRI-ARCBLADE AND BRUSHCUTTER GUARD SLOT LOOSEN TIGHTENGEAR HEAD FLANGED WASHER SLOT CUPPED WASHER GASOLINE OPERATIONFUEL MIXTURE FUEL MIXTURE HIGH QUALITY 2-CYCLEENGINE OILSee Figures 16 and TO ADVANCE THE CUTTING LINETO ADVANCE THE CUTTING LINE MANUALLY CUTTING TIPSCUTTING TECHNIQUE - BLADE See Figures 19 andBLADE THRUST TRI-ARCBLADETO STOP THE ENGINE IGNITION SWITCH THROTTLE TRIGGERPRIMER BULB STARTER GRIP IGNITION SWITCH STARTING See Figures 21, 22, andSee Figures 24 and MAINTENANCETo install the spool retainer NEW PREWOUND SPOOLFIRST STRING SLOT SECOND STRING See Figures 26, 27, andARROWS ON SPOOL ANCHOR HOLE FIRST STRINGFILTER SLOTS ON AIR FILTER BASE TABS ON AIR Cleaning InstructionsSee Figures 29 and LATCH PULL COVER TO OPENFUEL CAP SPARK PLUGSTORAGE 1 MONTH OR LONGER TROUBLESHOOTING IDLE SPEED SCREW MAINTENANCE REQUIREMENTS WARRANTYMANUFACTURERS WARRANTY COVERAGE OWNERSWARRANTY RESPONSIBILITIESAIR FILTER ASSY Emissions PartsEach Use 5 HoursNOTES • MODEL NO. AND SERIAL NO RYOBI TECHNOLOGIES INC• SERVICE • HOW TO ORDER REPAIR PARTS
Top Page Image Contents