Ryobi Outdoor SS30 ZR30002 Operation, See Figures 21, 22, and, To Stop The Engine, For Help Call

Page 18

See Figures 21, 22, and 23.

OPERATION

STARTING AND STOPPING

See Figures 21, 22, and 23.

Trimmer should be on a flat, bare surface for starting.

1.Slowly press the primer bulb seven (7) times.

2.Set the choke lever to the FULL CHOKE position (A).

3.Squeeze the throttle trigger fully and pull starter handle sharply until engine attempts to run. Do not pull the starter handle more than eight (8) times.

NOTE: Keep throttle trigger squeezed fully through STEP 6.

4.Set the choke lever to the HALF CHOKE position (B).

5.Pull the starter handle until the engine runs. Do not pull the starter handle more than six (6) times.

6.Allow the engine to run for 15 seconds, then set the choke lever to the RUN position (C).

TO STOP THE ENGINE:

See Figure 21.

To stop the engine, depress the switch to the stop position “ ”.

IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:

Do not return this product to the retail store where it was purchased. Please call our Customer Service Department for any issues you may have.

For Help Call: 1-800-860-4050

IGNITION SWITCH

THROTTLE

TRIGGER

Fig. 21

PRIMER BULB

STARTER GRIP

IGNITION

SWITCH

STARTING

INSTRUCTION

LABEL

THROTTLE TRIGGER

Fig. 22

CHOKE LEVER

RUN (C)

HALF

CHOKE (B)

FULL

CHOKE (A)

Fig. 23

Page 18

Image 18

Contents ZR30000 Series OPERATORS MANUAL30cc String Trimmers and Brushcutter SAVE THIS MANUAL FOR FUTURE REFERENCETABLE OF CONTENTS INTRODUCTIONGENERAL SAFETY RULES READ ALL INSTRUCTIONSSPECIFIC SAFETY RULES SPECIFIC SAFETY RULES FOR TRIMMER USENAME SYMBOLSSYMBOL EXPLANATIONSYMBOL SIGNAL SAVE THESE INSTRUCTIONSSERVICE MEANINGWeight - without fuel SPECIFICATIONSUNPACKING String cutting widthREAR HANDLE FEATURESHOUSING FRONT HANDLE KNOB CURVED SHAFT GRASS CHOKE LEVER COUPLER THROTTLE TRIGGER DRIVE SHAFTCOUPLER COUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSINGSTARTER GRIP THROTTLE TRIGGERSTRING TRIMMER SHAFT COUPLER GUIDE RECESS BUTTON ASSEMBLYSee Figure POSITIONING HOLE KNOBBOLT 1/4-20x 1 in. BOLT FRONT1/4-20 x 1 1/2 in FRONT HANDLE LOCK WASHER WING NUT BOLTFLAT WASHER HANDLE STRAP HANGER CLAMPBOLT BRACKET TO ATTACH THE CURVED SHAFT GRASS DEFLECTORZR30000 See Figure SLOT GEAR HEADREMOVING THE TRI-ARCBLADE AND BRUSHCUTTER GUARD GEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLYLATCH STRAP HANGER SHOULDER See Figures 10 andINSTALLING THE TRI-ARCBLADE AND BRUSHCUTTER GUARD SLOT LOOSEN TIGHTENGEAR HEAD FLANGED WASHER SLOT CUPPED WASHER FUEL MIXTURE HIGH QUALITY 2-CYCLEENGINE OIL OPERATIONFUEL MIXTURE GASOLINECUTTING TIPS TO ADVANCE THE CUTTING LINETO ADVANCE THE CUTTING LINE MANUALLY See Figures 16 andTRI-ARCBLADE See Figures 19 andBLADE THRUST CUTTING TECHNIQUE - BLADESee Figures 21, 22, and IGNITION SWITCH THROTTLE TRIGGERPRIMER BULB STARTER GRIP IGNITION SWITCH STARTING TO STOP THE ENGINENEW PREWOUND SPOOL MAINTENANCETo install the spool retainer See Figures 24 andFIRST STRING See Figures 26, 27, andARROWS ON SPOOL ANCHOR HOLE FIRST STRING SLOT SECOND STRINGLATCH PULL COVER TO OPEN Cleaning InstructionsSee Figures 29 and FILTER SLOTS ON AIR FILTER BASE TABS ON AIRFUEL CAP SPARK PLUGSTORAGE 1 MONTH OR LONGER TROUBLESHOOTING IDLE SPEED SCREW OWNERSWARRANTY RESPONSIBILITIES WARRANTYMANUFACTURERS WARRANTY COVERAGE MAINTENANCE REQUIREMENTS5 Hours Emissions PartsEach Use AIR FILTER ASSYNOTES • HOW TO ORDER REPAIR PARTS RYOBI TECHNOLOGIES INC• SERVICE • MODEL NO. AND SERIAL NO