Ryobi Outdoor SS30 ZR30002 Maintenance, Cleaning Instructions, See Figures 29 and, Filter Cover

Page 21

Cleaning Instructions:

MAINTENANCE

CLEANING THE EXHAUST PORT AND MUFFLER

Depending on the type of fuel used, the type and amount of oil used, and/or your operating conditions, the exhaust port and muffler may become blocked with carbon deposits. If you notice a power loss with your gas powered tool, a qualified service technician will need to remove these deposits to restore performance.

SPARK ARRESTOR

The spark arrestor must be cleaned or replaced every 25 hours or yearly to ensure proper performance of your product. Spark arrestors may be in different locations depending on the model purchased. Please contact your nearest service dealer for the location of the spark arrestor for your model.

Cleaning Instructions:

■Remove the spark arrestor from the muffler.

■If your spark arrestor is made of a fiberglass material, discard and replace.

■If your spark arrestor is made of a metal material follow these cleaning instructions:

1.Spray the spark arrestor with a quality carbon cleaner.

2.Gently clean using a wire brush.

3.Install the new or cleaned spark arrestor and reas- semble completely before use.

REPLACING AND CLEANING AIR FILTER

See Figures 29 and 30.

For proper performance and long life, keep air filter clean.

1Remove the air filter cover by pushing down on the latch with your thumb while gently pulling on the cover.

2Remove the filter, clean it in warm soapy water. Rinse and let dry completely. For best performance, replace annually.

3Reinstall the filter.

4Replace the air filter cover by inserting the tabs on the bottom of the cover into the slots on the air filter base; push the cover up until it latches securely in place.

LATCH

PULL COVER

TO OPEN

Fig. 29

FILTER

SLOTS ON AIR

FILTER BASE

TABS ON AIR

FILTER COVER

Fig. 30

Page 21

Image 21

Contents 30cc String Trimmers and Brushcutter OPERATORS MANUALZR30000 Series SAVE THIS MANUAL FOR FUTURE REFERENCEINTRODUCTION TABLE OF CONTENTSREAD ALL INSTRUCTIONS GENERAL SAFETY RULESSPECIFIC SAFETY RULES FOR TRIMMER USE SPECIFIC SAFETY RULESSYMBOL SYMBOLSNAME EXPLANATIONSERVICE SAVE THESE INSTRUCTIONSSYMBOL SIGNAL MEANINGUNPACKING SPECIFICATIONSWeight - without fuel String cutting widthHOUSING FRONT HANDLE KNOB CURVED SHAFT GRASS FEATURESREAR HANDLE CHOKE LEVER COUPLER THROTTLE TRIGGER DRIVE SHAFTSTARTER GRIP COUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSINGCOUPLER THROTTLE TRIGGERSee Figure ASSEMBLYSTRING TRIMMER SHAFT COUPLER GUIDE RECESS BUTTON POSITIONING HOLE KNOBFLAT WASHER FRONT HANDLE LOCK WASHER WING NUT BOLTBOLT 1/4-20x 1 in. BOLT FRONT1/4-20 x 1 1/2 in HANDLE STRAP HANGER CLAMPZR30000 See Figure TO ATTACH THE CURVED SHAFT GRASS DEFLECTORBOLT BRACKET SLOT GEAR HEADLATCH STRAP HANGER SHOULDER GEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLYREMOVING THE TRI-ARCBLADE AND BRUSHCUTTER GUARD See Figures 10 andINSTALLING THE TRI-ARCBLADE AND BRUSHCUTTER GUARD SLOT LOOSEN TIGHTENGEAR HEAD FLANGED WASHER SLOT CUPPED WASHER FUEL MIXTURE OPERATIONFUEL MIXTURE HIGH QUALITY 2-CYCLEENGINE OIL GASOLINETO ADVANCE THE CUTTING LINE MANUALLY TO ADVANCE THE CUTTING LINECUTTING TIPS See Figures 16 andBLADE THRUST See Figures 19 andTRI-ARCBLADE CUTTING TECHNIQUE - BLADEPRIMER BULB STARTER GRIP IGNITION SWITCH STARTING IGNITION SWITCH THROTTLE TRIGGERSee Figures 21, 22, and TO STOP THE ENGINETo install the spool retainer MAINTENANCENEW PREWOUND SPOOL See Figures 24 andARROWS ON SPOOL ANCHOR HOLE See Figures 26, 27, andFIRST STRING FIRST STRING SLOT SECOND STRINGSee Figures 29 and Cleaning InstructionsLATCH PULL COVER TO OPEN FILTER SLOTS ON AIR FILTER BASE TABS ON AIRFUEL CAP SPARK PLUGSTORAGE 1 MONTH OR LONGER TROUBLESHOOTING IDLE SPEED SCREW MANUFACTURERS WARRANTY COVERAGE WARRANTYOWNERSWARRANTY RESPONSIBILITIES MAINTENANCE REQUIREMENTSEach Use Emissions Parts5 Hours AIR FILTER ASSYNOTES • SERVICE RYOBI TECHNOLOGIES INC• HOW TO ORDER REPAIR PARTS • MODEL NO. AND SERIAL NO