Ryobi Outdoor CS30 ZR30000 Assembly, Latch Strap Hanger Shoulder, See Figures 10 and, Slot

Page 13
LATCH

ASSEMBLY

ATTACHING THE SHOULDER HARNESS - ZR30004

See Figure 9.

1.Connect the latch on the shoulder harness to the strap hanger.

2.Adjust the strap to a comfortable position.

CONVERTING FROM BRUSHCUTTER TO STRING TRIMMER - ZR30004

To convert from the brushcutter to the string trimmer, remove the blade and brushcutter guard, attach the straight

LATCH

STRAP HANGER

SHOULDER

shaft grass deflector and install the string head.

REMOVING THE TRI-ARC® BLADE AND

BRUSHCUTTER GUARD

See Figures 10 and 11.

1.

Align the slot in the flanged washer with the slot in the

 

gear head.

2.

Place the gear head locking tool through the slot in the

 

flanged washer and gear head.

3.

Remove the blade nut by turning it clockwise.

HARNESS

GEAR HEAD

LOCKING TOOL

Fig. 9

4.

Remove the cupped washer and the blade

5.

Remove the flanged washer from the gear head shaft

 

and retain it for the string head installation.

6.

Remove the three screws securing the brushcutter guard

 

to gear head.

7.

Remove the brushcutter guard.

NOTE: Store the brushcutter parts together for later use.

INSTALLING THE STRAIGHT SHAFT GRASS DEFLEC- TOR AND STRING HEAD

See Figures 10 and 12.

1.Install the grass deflector. Refer to “To Attach the Straight Shaft Grass Deflector” earlier in this manual.

2.Place the flanged washer on the gear head shaft.

NOTE: The hollow side of the flanged washer should face the gear head.

2.Align the slot in the flanged washer with the slot in the gear head.

3.Place the gear head locking tool through the slot in the flanged washer and gear head.

4.Install the string head assembly onto the gear head shaft by turning counterclockwise.

6. Tighten the string head assembly securely.

Fig. 10

GEAR HEAD

BRUSHCUTTER

GUARD

FLANGED WASHER

SLOT

CUPPED REMOVING THE TRI-ARC® BLADE AND

WASHER

BLADE NUT

Fig. 11

 

 

GEAR HEAD

FLANGED WASHER

STRING HEAD

ASSEMBLY

SLOT

LOOSEN

TIGHTEN

Fig. 12

Page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 30cc String Trimmers and Brushcutter OPERATORS MANUALZR30000 Series SAVE THIS MANUAL FOR FUTURE REFERENCEINTRODUCTION TABLE OF CONTENTSREAD ALL INSTRUCTIONS GENERAL SAFETY RULESSPECIFIC SAFETY RULES FOR TRIMMER USE SPECIFIC SAFETY RULESSYMBOL SYMBOLSNAME EXPLANATIONSERVICE SAVE THESE INSTRUCTIONSSYMBOL SIGNAL MEANINGUNPACKING SPECIFICATIONSWeight - without fuel String cutting widthHOUSING FRONT HANDLE KNOB CURVED SHAFT GRASS FEATURESREAR HANDLE CHOKE LEVER COUPLER THROTTLE TRIGGER DRIVE SHAFTSTARTER GRIP COUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSINGCOUPLER THROTTLE TRIGGERSee Figure ASSEMBLYSTRING TRIMMER SHAFT COUPLER GUIDE RECESS BUTTON POSITIONING HOLE KNOBFLAT WASHER FRONT HANDLE LOCK WASHER WING NUT BOLTBOLT 1/4-20x 1 in. BOLT FRONT1/4-20 x 1 1/2 in HANDLE STRAP HANGER CLAMPZR30000 See Figure TO ATTACH THE CURVED SHAFT GRASS DEFLECTORBOLT BRACKET SLOT GEAR HEADLATCH STRAP HANGER SHOULDER GEAR HEAD FLANGED WASHER STRING HEAD ASSEMBLYREMOVING THE TRI-ARCBLADE AND BRUSHCUTTER GUARD See Figures 10 andSLOT LOOSEN TIGHTEN INSTALLING THE TRI-ARCBLADE AND BRUSHCUTTER GUARDGEAR HEAD FLANGED WASHER SLOT CUPPED WASHER FUEL MIXTURE OPERATIONFUEL MIXTURE HIGH QUALITY 2-CYCLEENGINE OIL GASOLINETO ADVANCE THE CUTTING LINE MANUALLY TO ADVANCE THE CUTTING LINECUTTING TIPS See Figures 16 andBLADE THRUST See Figures 19 andTRI-ARCBLADE CUTTING TECHNIQUE - BLADEPRIMER BULB STARTER GRIP IGNITION SWITCH STARTING IGNITION SWITCH THROTTLE TRIGGERSee Figures 21, 22, and TO STOP THE ENGINETo install the spool retainer MAINTENANCENEW PREWOUND SPOOL See Figures 24 andARROWS ON SPOOL ANCHOR HOLE See Figures 26, 27, andFIRST STRING FIRST STRING SLOT SECOND STRINGSee Figures 29 and Cleaning InstructionsLATCH PULL COVER TO OPEN FILTER SLOTS ON AIR FILTER BASE TABS ON AIRSPARK PLUG FUEL CAPSTORAGE 1 MONTH OR LONGER TROUBLESHOOTING IDLE SPEED SCREW MANUFACTURERS WARRANTY COVERAGE WARRANTYOWNERSWARRANTY RESPONSIBILITIES MAINTENANCE REQUIREMENTSEach Use Emissions Parts5 Hours AIR FILTER ASSYNOTES • SERVICE RYOBI TECHNOLOGIES INC• HOW TO ORDER REPAIR PARTS • MODEL NO. AND SERIAL NO
Top Page Image Contents