Ryobi Outdoor 3000 PSI, RY80030A manual Replacing the Fuel Hose

Page 17

MAINTENANCE

changing the oil

See Figure 20.

nShut off the engine.

nPlace a container under the pressure washer.

nRemove the oil drain plug and drain the old oil.

NOTE: Drain the oil while the engine is still warm but not hot. Warm oil will drain quickly and more completely.

nReplace the oil drain plug.

nReplace the oil with new, clean oil. This engine will hold 20 oz. or .6 liters of oil (10W-30).

NOTE: Consult hazardous waste management guidelines in your area for the proper way to dispose of used fuel.

checking a fouled spark plug

See Figure 21.

nClean carbon deposits off the spark plug electrode using a plug cleaner or wire brush.

nCheck electrode gap. The gap should be .6 mm - .7 mm. Adjust the gap, if necessary, by carefully bending the side electrode.

(Recommended spark plug: NGK BR-6HS; CHAMPION RL86C.)

CLEANing FUEL CUP

See Figure 22.

nInspect fuel cup for water and dirt.

nIf dirt or water is present,close the fuel valve and remove the fuel cup. Using a wrench, grasp the square on the bottom of the fuel cup and turn clockwise.

nAfter removing dirt and water, wash the fuel cup with kerosene or gasoline. Reinstall securely to prevent leak- age.

nozzle maintenance

See Figure 23.

Excessive pump pressure (a pulsing sensation felt while squeezing the trigger) may be the result of a clogged or dirty nozzle.

n Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure.

nRemove the nozzle from the spray wand.

NOTE: Never point the spray wand at your face.

nUsing the nozzle cleaning tool provided, free any foreign materials clogging or restricting the nozzle.

nUsing a garden hose, flush debris out of nozzle by back flushing (running the water through the nozzle backwards or from the outside to the inside).

nReinstall the nozzle then reconnect the nozzle to the spray wand.

nTurn on the water supply and start the engine.

0.6 - 0.7mm

Fig. 21

TO TIGHTEN

FUEL CUP

TO LOOSEN

Fig. 22

 

nozzle

cleaning tool

nozzle

Fig. 23

REPLACING THE FUEL HOSE

Replace the fuel hose every 1,000 hours of use. If fuel leaks from fuel hose, replace the hose immediately.

pump maintenance

We recommend having the pump oil changed every 100 hours to ensure longer life of the machine. This service should be performed by an authorized service center.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions Before Using this Product Important Safety InstructionsSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsService Wand ON/OFF Switch Product SpecificationsRecoil BucketFeatures Attaching the wheel assembly AssemblyUnpacking Packing ListAttaching the resting foot Connecting high pressure hose to spray wand AssemblyAssembling the spray wand Attaching Injection hoseAdding gasoline to the Fuel tank Adding oil to the engineOIL CAP / DIPSTICK Upper Level Fuel CAP FunnelQuick-connect Collar Garden Hose Screen To connect the garden hose to the machineApplications OperationStarting/stopping the pressure washer Recoil StarterSELECTing the Right QUICK-CONNECT Using the spray wand triggerNozzle for the JOB cautionStoring the pressure washer Moving the pressure washerWashing with detergent Rinsing with the pressure washerGeneral Maintenance MaintenanceCleaning the air filter Wire MeshReplacing the Fuel Hose Preparing for use after storage Periodic maintenance schedule tableProblem Cause Solution TroubleshootingPage Warranty General Emissions Warranty Coverage Parts Covered Under the California Emissions Warranty Warranty Periods Limited ROBIN/SUBARU Engine WarrantyLimited NON-ENGINE Warranty Statement California Proposition Service Model NO. and Serial no
Top Page Image Contents