Ryobi Outdoor 3000 PSI, RY80030A manual Parts Covered Under the California Emissions Warranty

Page 23

WARRANTY

When warranty repair is needed, the engine must be brought to an authorized service dealer or warranty station’s place of business during normal business hours. In all cases, a reasonable time, not to exceed 30 days, must be allowed for the warranty repair to be completed after the engine is received by the authorized service dealer or warranty station.

MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS

Only warranted engine replacement parts approved by FUJI should be used in the performance of any warranty maintenance or repairs on emission-related parts. If other than authorized parts are used for maintenance, replacement, or repair of components affecting emission control, you should assure yourself that such parts are warranted by their manufacturer to be equivalent to authorized parts in performance and durability. FUJI, however, assumes no liability under this warranty with respect to parts other than authorized parts. The use of non-authorized replacement parts does not invalidate the warranty on other components unless the non-authorized parts cause damage to warranted parts.

PARTS COVERED UNDER THE CALIFORNIA EMISSIONS WARRANTY

The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty

HIGH ALTITUDE ENGINE OPERATION■

coverage if FUJI demonstrates that the engine has been abused, neglected, or improperly maintained, and that such abuse , neglect ,or improper maintenance was the direct cause of the need for repair or replacement of the part. That notwithstanding, any adjustment of a component that has a factory installed, and properly operating, adjustment limiting device is still eligible for warranty coverage. The following emissions warranty parts list are covered.

(1)Fuel Metering System

(i)Carburetor and internal parts (and/or pressure regulator or fuel injection system).

(ii)Air/fuel ratio feedback and control system, if applicable.

(iii)Cold start enrichment system, if applicable.

(iv)Regulator assembly (gaseous fuel, if applicable).

(2)Air Induction System

(i)Intake manifold, if applicable.

(ii)Air filter

(3)Ignition System

(i)Spark plugs.

(ii)Magneto or electronic ignition system.

(iii)Spark advance/retard system, if applicable.

(4)Exhaust manifold, if applicable.

(5)Evaporation Systems

(i)Fuel lines.

(ii)Fuel line fittings.

Please have an authorized Robin America service dealer modify this engine if it is to be run continuously above 5000 feet (1500 meters). Failure to do so, may result in poor engine performance, spark plug fouling, hard starting, and increased emissions.■

Carburetor modification by an authorized Robin America service dealer will improve performance and allow that this engine meets EPA (Environmental Protection Agency) and California ARB (Air Resources Board) emission standards throughout its useful life.■

An engine converted for high altitudes can not be run at 5000 feet or lower. In doing so, the engine will overheat and cause serious engine damage. Please have an authorized Robin America service dealer restore high altitude modified engines to the original factory specification before operating below 5000 feet.

AIR INDEX

To show compliance with California emission regulations, a hangtag has been provided displaying the Air Index level and durability period of this engine.

The Air Index level defines how clean an engine’s exhaust is over a period of time. A bar graph scaled from “0” (most clean) to “10” (least clean) is used to show an engine’s Air Index level. A lower Air Index level represents cleaner exhaust from an engine. The period of time (in hours) that the Air Index level is measured is known as the durability period. Depending on the size of the engine, a selection of time periods can be used to measure the Air Index level (see below).

Descriptive Term

Applicable to Emissions Durability Period

Moderate

50 hours (engine from 0 to 80 cc)

 

125 hours (engine greater than 80 cc)

Intermediate

125 hours (engine from 0 to 80 cc)

 

250 hours (engine greater than 80 cc)

Extended

300 hours (engine from 0 to 80 cc)

 

500 hours (engine greater than 80 cc)

Notice: This hangtag must remain on this engine or piece of equipment, and only be removed by the ultimate purchaser before operation.

Valve Clearance

0.12+0.030

mm (0.0047 +0.00120

in.)

(Intake and Exhaust)

Note: Adjust the valve clearance while the engine is cold.

Emissions Durability Period

500 hours

 

(California only)

 

 

 

23

Image 23
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions Before Using this Product Important Safety InstructionsSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsService Bucket Product SpecificationsWand ON/OFF Switch RecoilFeatures Packing List AssemblyAttaching the wheel assembly UnpackingAttaching Injection hose Connecting high pressure hose to spray wand AssemblyAttaching the resting foot Assembling the spray wandFuel CAP Funnel Adding oil to the engineAdding gasoline to the Fuel tank OIL CAP / DIPSTICK Upper LevelQuick-connect Collar Garden Hose Screen To connect the garden hose to the machineRecoil Starter OperationApplications Starting/stopping the pressure washercaution Using the spray wand triggerSELECTing the Right QUICK-CONNECT Nozzle for the JOBRinsing with the pressure washer Moving the pressure washerStoring the pressure washer Washing with detergentWire Mesh MaintenanceGeneral Maintenance Cleaning the air filterReplacing the Fuel Hose Preparing for use after storage Periodic maintenance schedule tableProblem Cause Solution TroubleshootingPage Warranty General Emissions Warranty Coverage Parts Covered Under the California Emissions Warranty Warranty Periods Limited ROBIN/SUBARU Engine WarrantyLimited NON-ENGINE Warranty Statement California Proposition Service Model NO. and Serial no