Ryobi Outdoor 3000 PSI, RY80030A Assembly, Unpacking, Packing List, Attaching the wheel assembly

Page 9

ASSEMBLY

UNPACKING

This product requires assembly.

nCarefully cut the box down the sides then remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included.

NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed.

nRemove and discard the clear cap securing the operator’s manual bag to the pump breather tube.

nInspect the tool carefully to make sure no breakage or damage occurred during shipping.

nDo not discard the packing material until you have care- fully inspected and satisfactorily operated the tool.

nIf any parts are damaged or missing, please call 1-800-860-4050 for assistance.

PACKING LIST

Pressure Washer

30 ft. High Pressure Hose Spray Wand Assembly (upper) Assist Handle Assembly Spray Wand Extension (lower) Quick-Connect Nozzle (5) Nozzle Cleaning Tool Resting Foot

Axle Assembly (2) Wheel (2) Washer (2) Hardware Bag

4-Cycle Engine Oil (10W-30) Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this tool until the missing parts are replaced. Failure to heed this warning could result in possible serious personal injury.

hitch

pin

AXLE

WASHER

WARNING:

Do not attempt to modify this tool or create accesso- ries not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING:

To prevent accidental starting that could cause serious personal injury, always disconnect the engine spark plug wire from the spark plug when assembling parts.

NOTE: Do not start the pressure washer until the engine has been filled with oil and all hoses are connected. Running this machine without oil will damage the engine while running it without water will damage the high pressure pump.

attaching the wheel assembly

See Figure 2.

To attach the wheels to the pressure washer base:

nLocate the axle assembly; remove the hitch pin from the axle.

nSlip the axle into the wheel hole and slide the washer onto the axle.

nLift the machine and slide the axle/wheel/washer combination into the wheel mounting hole in the machine base as shown.

nPush the hitch pin into the hole on the end of the axle to secure the wheel assembly.

NOTE: The hitch pin should be pushed into the axle until the center of the pin rests on top of the axle.

nRepeat with the second wheel assembly.

NOTE: It is important to always maintain proper air pressure in both wheels.

Fig. 2

Image 9
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions Before Using this Product Important Safety InstructionsSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsService Wand ON/OFF Switch Product SpecificationsRecoil BucketFeatures Attaching the wheel assembly AssemblyUnpacking Packing ListAttaching the resting foot Connecting high pressure hose to spray wand AssemblyAssembling the spray wand Attaching Injection hoseAdding gasoline to the Fuel tank Adding oil to the engineOIL CAP / DIPSTICK Upper Level Fuel CAP FunnelQuick-connect Collar Garden Hose Screen To connect the garden hose to the machineApplications OperationStarting/stopping the pressure washer Recoil StarterSELECTing the Right QUICK-CONNECT Using the spray wand triggerNozzle for the JOB cautionStoring the pressure washer Moving the pressure washerWashing with detergent Rinsing with the pressure washerGeneral Maintenance MaintenanceCleaning the air filter Wire MeshReplacing the Fuel Hose Preparing for use after storage Periodic maintenance schedule tableProblem Cause Solution TroubleshootingPage Warranty General Emissions Warranty Coverage Parts Covered Under the California Emissions Warranty Warranty Periods Limited ROBIN/SUBARU Engine WarrantyLimited NON-ENGINE Warranty Statement California Proposition Service Model NO. and Serial no