Ryobi Outdoor CS30 RY30020B, SS30 RY30040B, BC30 RY30060B manual Attaching the J Handle BC30

Page 11

ASSEMBLY

ATTACHING THE FRONT HANDLE - CS30 AND SS30

See Figure 4.

nRemove the front handle, bolt, flat washer, lock washer, and wing nut from the Operator’s Kit.

nInstall the front handle onto the top side of the drive shaft housing and move it to a comfortable position.

nPlace the bolt through the front handle.

NOTE: The hex bolt head fits inside the hex recess molded into one side of the handle.

nInstall the flat washer, lock washer, and wing nut.

nTighten wing nut securely.

ATTACHING THE “J” HANDLE - BC30

See Figure 5.

A “J” handle must be used for ensuring the best control and maximizing operator safety when using a brushcutter.

nHold the top and bottom clamp snugly in position on the shaft housing so that handle will be located to the operator’s left.

nInsert the end of the handle between the clamps.

nAlign the bolt holes and push the long bolt (1/4-20 x 1-1/2 in.) through the handle side.

nPlace short bolt (1/4-20 x 1 in.) through opposite side of clamp. Install flat washers, lock washers, and hex nuts to hold the assembly in place.

nAfter assembly is complete, adjust the position of the handle for best balance and comfort.

nTighten first the long bolt and then the short bolt.

FRONT HANDLE	LOCK
	LOCK
	WASHER

WING

NUT

BOLT

	FLAT WASHER		Fig. 4
			Fig. 4
	BOLT
FRONT	1/4-20 x 1 in.	BOLT
		BOLT
		1/4-20 x 1 1/2 in.
HANDLE		1/4-20 x 1 1/2 in.
HANDLE
			STRAP
			HANGER
CLAMP

CLAMP	FLAT WASHER
	LOCK WASHER
HEX NUT	Fig. 5

Page 11

Image 11

Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules for BRUSH- Cutter and Blade USE Specific Safety RulesSpecific Safety Rules for Trimmer USE Symbol Name Explanation SymbolsService Features Knob Straight Shaft Grass Deflector Starter GripRope Trigger Lock PrimerAssembly See Figure Installing the Power Head to the AttachmentRemoving the Attachment from the Power Head Attaching the Storage HangerAttaching the J Handle BC30 Attaching the Front Handle CS30 and SS30Attaching the Brushcutter Guard BC30 Attaching the Grass DeflectorTo Attach the Curved Shaft Grass Deflector CS30 To Attach the Straight Shaft Grass Deflector SS30Converting from String Trimmer to Brushcutter BC30 Attaching the Shoulder Harness BC30Converting from Brushcutter to String Trimmer BC30 Removing the TRI-ARCBLADE and Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Installing the TRI-ARCBLADE and Brushcutter GuardOperation Operating the Trimmer Fueling and Refueling the TrimmerGrass Deflector Line Trimming CUT-OFF Blade To Advance the Cutting LineTo Advance the Cutting Line Manually Cutting TipsCutting Technique Blade Operating the BrushcutterBlade Thrust TRI-ARCBLADESee Figures 21 Starting and StoppingSee Figures 24 MaintenanceGeneral Maintenance Spool ReplacementFirst String Slot String ReplacementSee Figures 26 Arrows on Spool Anchor HoleSpark Plug Cleaning the Exhaust Port and Muffler Spark ArrestorReplacing and Cleaning AIR Filter Fuel CAPIdle Speed Screw TroubleshootingSpeed. See Figure This Product WAS Manufactured with a Catalyst Muffler WarrantyLimited Warranty Statement Coverage MANUFACTURER’S Warranty CoverageOWNER’S Warranty Responsibilities Maintenance RequirementsService