Ryobi Outdoor CS30 RY30020B, SS30 RY30040B, BC30 RY30060B String Replacement, See Figures 26

Page 20

MAINTENANCE

To install the spool retainer:

nTurn the spool retainer clockwise for model CS30. Turn the spool retainer counterclockwise for models SS30 and BC30.

nPull the strings again to rotate the spool into cutting position. Push the spool retainer down while pulling on string(s) to manually advance the string and to check for proper assembly of the string head.

STRING REPLACEMENT

See Figures 26 - 28.

SPRING

SPOOL

ARROWS ON

SPOOL

ANCHOR

HOLE

Use only monofilament string. Use original manufacturer’s replacement string for best performance.

String Diameter:

CS30 - .080 in. (2.0 mm)

SS30 - .095 in. (2.4 mm)

BC30 - .095 in. (2.4 mm)

nStop the engine, disconnect the spark plug wire. Hold the string head and unscrew the spool retainer.

To remove the spool retainer:

n Turn the spool retainer counterclockwise for models CS30.

FIRST STRING

FIRST STRING

SLOT

Fig. 26

Turn the spool retainer clockwise for models SS30 and

BC30.

n Remove the spool from the string head.

NOTE: Keep the spring attached to the spool. Remove

any old string remaining on the spool.

n Cut two pieces of string, each being approximately 9 ft.

(2.7 m) long.

n Insert the first string into the anchor hole in the upper part

of the spool. Wind the first string around the upper part of

the spool counterclockwise, as shown by the arrows on

the spool. Place string in the slot on upper spool flange,

leaving about 6 in. (152 mm) extended beyond the slot.

Do not overfill. After winding the string, there should be

at least 1/4 in. (6 mm) between the wound string and the

outside edge of the spool.

n Repeat above step with second string, using the bottom

part of spool. Do not overfill.

n Replace the spool and the spool retainer. Refer to “Spool

Replacement” earlier in this manual.

SECOND

STRING

Fig. 27

SLOT

ARROWS ON

 

SPOOL

Fig. 28

Page 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules for BRUSH- Cutter and Blade USE Specific Safety RulesSpecific Safety Rules for Trimmer USE Symbols Symbol Name ExplanationService Features Starter Grip RopeTrigger Lock Primer Knob Straight Shaft Grass DeflectorAssembly Installing the Power Head to the Attachment Removing the Attachment from the Power HeadAttaching the Storage Hanger See FigureAttaching the Front Handle CS30 and SS30 Attaching the J Handle BC30Attaching the Grass Deflector To Attach the Curved Shaft Grass Deflector CS30To Attach the Straight Shaft Grass Deflector SS30 Attaching the Brushcutter Guard BC30Attaching the Shoulder Harness BC30 Converting from Brushcutter to String Trimmer BC30Removing the TRI-ARCBLADE and Brushcutter Guard Converting from String Trimmer to Brushcutter BC30Removing the Straight Shaft Grass Deflector and String Head Installing the TRI-ARCBLADE and Brushcutter GuardOperation Fueling and Refueling the Trimmer Operating the TrimmerTo Advance the Cutting Line To Advance the Cutting Line ManuallyCutting Tips Grass Deflector Line Trimming CUT-OFF BladeOperating the Brushcutter Blade ThrustTRI-ARCBLADE Cutting Technique BladeStarting and Stopping See Figures 21Maintenance General MaintenanceSpool Replacement See Figures 24String Replacement See Figures 26Arrows on Spool Anchor Hole First String SlotCleaning the Exhaust Port and Muffler Spark Arrestor Replacing and Cleaning AIR FilterFuel CAP Spark PlugIdle Speed Screw TroubleshootingSpeed. See Figure Warranty This Product WAS Manufactured with a Catalyst MufflerLimited Warranty Statement MANUFACTURER’S Warranty Coverage OWNER’S Warranty ResponsibilitiesMaintenance Requirements CoverageService
Top Page Image Contents