Ryobi Outdoor CS30 RY30020B, SS30 RY30040B, BC30 RY30060B General Maintenance, See Figures 24

Page 19

MAINTENANCE

WARNING:

When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.

WARNING:

Always wear safety goggles or safety glasses with side shields during tool operation. If operation is dusty, also wear a dust mask.

WARNING:

Before inspecting, cleaning, or servicing the machine, shut off engine, wait for all moving parts to stop, and disconnect spark plug wire and move it away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

You can often make adjustments and repairs described here. For other repairs, have the trimmer serviced by an authorized service dealer.

SPOOL REPLACEMENT

NEW PREWOUND SPOOL

See Figures 24 - 25.

If replacing string only, refer to “String Replacement” later in this manual.

Use only monofilament string. Use original manufacturer’s replacement string for best performance.

String Diameter:

CS30 - .080 in. (2.0 mm)

SS30 - .095 in. (2.4 mm)

BC30 - .095 in. (2.4 mm)

nStop the engine and disconnect the spark plug wire. Hold the string head and unscrew the spool retainer.

To remove the spool retainer:

nTurn the spool retainer counterclockwise for model CS30. Turn the spool retainer clockwise for models SS30 and BC30.

SPOOL

RETAINER

Fig. 24

SPRING

SLOTS

EYELETS

STRING HEAD

SHAFT

Fig. 25

nRemove the empty spool from the string head. Keep the spring attached to the spool.

nTo install the new spool, make sure the two strings are captured in the slots opposite each other on the new spool. Make sure the ends of each string are extended approximately 6 in. (152 mm) beyond each slot.

nThread the strings into the eyelets in the string head. Carefully push the spool into the string head (gently pull the strings to the outside if necessary). When the spool is positioned in the string head, grasp the strings and pull sharply to release them from the slots in the spool.

nPush down and turn the spool counterclockwise until it no longer turns. Hold the spool down and rotate clockwise a small amount. Release the spool. The spool should be locked down in the string head. If not, hold down and rotate until locked.

nMake sure the string head and the spool retainer are installed on the drive shaft.

Page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules for Trimmer USE Specific Safety RulesSpecific Safety Rules for BRUSH- Cutter and Blade USE Symbol Name Explanation SymbolsService Features Knob Straight Shaft Grass Deflector Starter GripRope Trigger Lock PrimerAssembly See Figure Installing the Power Head to the AttachmentRemoving the Attachment from the Power Head Attaching the Storage HangerAttaching the J Handle BC30 Attaching the Front Handle CS30 and SS30Attaching the Brushcutter Guard BC30 Attaching the Grass DeflectorTo Attach the Curved Shaft Grass Deflector CS30 To Attach the Straight Shaft Grass Deflector SS30Converting from String Trimmer to Brushcutter BC30 Attaching the Shoulder Harness BC30Converting from Brushcutter to String Trimmer BC30 Removing the TRI-ARCBLADE and Brushcutter GuardOperation Installing the TRI-ARCBLADE and Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Operating the Trimmer Fueling and Refueling the TrimmerGrass Deflector Line Trimming CUT-OFF Blade To Advance the Cutting LineTo Advance the Cutting Line Manually Cutting TipsCutting Technique Blade Operating the BrushcutterBlade Thrust TRI-ARCBLADESee Figures 21 Starting and StoppingSee Figures 24 MaintenanceGeneral Maintenance Spool ReplacementFirst String Slot String ReplacementSee Figures 26 Arrows on Spool Anchor HoleSpark Plug Cleaning the Exhaust Port and Muffler Spark ArrestorReplacing and Cleaning AIR Filter Fuel CAPSpeed. See Figure TroubleshootingIdle Speed Screw This Product WAS Manufactured with a Catalyst Muffler WarrantyLimited Warranty Statement Coverage MANUFACTURER’S Warranty CoverageOWNER’S Warranty Responsibilities Maintenance RequirementsService
Top Page Image Contents