KEF Audio KIT100 installation manual Pre-programmed remote control, KEF services

Page 21

pre-programmed remote control

DEVICE

The remote control will operate the KIT100 DVD Home Theatre System when you press the DVD device key.The other device keys can be set to operate other equipment and are selected by pressing the required device key.The alternative key functionality of the remote control can be seen in “Remote control alternative keys functionality table” on page 46.

In order to record on aVCR it is necessary to press both the record (OPEN/CLOSE) and PLAY keys at the same time.

If the batteries are replaced in the remote control within five minutes then the programmed IR codes will be remembered. If the batteries are removed for longer the remote may need to be re- programmed.

 

 

Quick programming the remote control

 

 

 

 

 

 

In the user manual for the equipment you wish to program, you should find a 3 or 4 digit product IR

 

 

code. If this is not given then look up the 4 digit code in the “Equipment manufactures IR codes

 

 

table” on page 39 for the brand of equipment that you have. If there are several product IR codes

 

 

then you will need to try them in turn until successful operation is achieved. Follow the quick

 

 

programming sequence below. If a key is not pressed for 10 seconds then the programming process

 

 

will stop automatically, and you will have to start again.To exit the programming mode press any

SOURCE

DEVICE key so that the LED turns off.

 

 

1. obtain the product IR four digit code(s) from the table

 

 

2. press and hold the SET key and the required device key (TV,VCR, SAT or CBL) together until

 

 

the LED turns on

 

 

3. enter the four-digit code for your equipment using the numerical keys, the LED will blink for

 

 

each digit, the LED should then turn off.

 

 

If the LED flashes two times, to indicate that an invalid code was entered, then repeat step 3.

4.test the remote control with your equipment and if not successful, look up the next product IR code for your equipment's manufacturer and repeat the steps from 2.

Automatic search programming

If the products IR three or four digit code is not in the equipment manual or the “Equipment manufactures IR codes table” on page 39, or still dose not work correctly after completing the Quick programming steps above for all the listed codes, then you can get the remote control to automatically scroll through all the IR codes for each specific device type. Patience will be required as it can take several minutes for the remote control to go through each of the codes for that device type. Follow and repeat the automatic programming sequence below. If no key is pressed on the remote control for 30 seconds then the programming process will stop automatically, and you will have to start again.

1.turn on the equipment you wish to operate with the remote control (if the equipment is aVCR then insert a tape and start playback) and ensure that the remote control remains pointing at the equipment

2.press and hold the SET key and the required device key (TV,VCR, SAT or CBL) together until the LED turns on

3.press and release the SET key again to enter the search mode, the LED will flash fast

4.Press and hold the POWER key for 3 seconds until the LED flashes every 2 seconds.This indicating that you are in the automatic search mode where a different IR code is transmitted automatically on each flash.

5.when your equipment turns off because it has received the correct power IR command, immediately press any key to stop the automatic search, the LED stops flashing

6.press any device key (TV,VCR, SAT or CBL) to store the current IR code, the LED will turn off

7.turn your equipment back on, press the correct device key (TV,VCR, SAT or CBL) and test the remote control for correct functionality. If it does not work fully then repeat the steps from 1.

8.If the remote controls LED turns off before your equipment receives a valid IR code to turn it off then repeat the above steps from 1 ensuring that the remote control is pointing at the equipment, that the equipment is switched on and that you chose the correct DEVICE type.

Reading the stored IR code

You can see what IR code is stored for each device key. Press the relevant device key (TV,VCR, SAT or CBL).Then press and hold SET and at the same time press digit 1, 2, 3 or 4 on the numeric keys, then release all keys. Each time you press SET and digit “1” to “4” the LED will flash the same number of times as that digit of the IR code number.

KEF services

Customer service

For additional help in solving problems, follow the trouble shooting section then contact KEF® customer service or your local retailer.

Warranty

The KEF Instant Theatre system is covered by a limited non-transferable warranty. Details of the warranty are provided on the warranty card that came with your system. Please fill out the information section on the card and return it.

Accessories

The KEF Instant Theatre system shelf speakers are compatible with the optional KEF Instant Theatre speaker floor stands.

20

Page 20 Page 22
Image 21
Page 20 Page 22
Contents GB Installation Manual Class 1 laser product Important safety instructionsClass B emissions limits BatteriesUsing the manual Carton contentsIntroduction Important pointsES guía rápida de procedimientos iniciales Quick start-up guidePower Onoff Positioning speakers Positioning subwoofer Tv connection options CompositeVideo Tv audio out ComponentAm aerial set-up Vcr/satellite advanced connection optionsVideo connection setup English instructionsUnpacking Dvd system controls DisplayDvd rear panel Remote control Settings menu System settingsLanguage menu Video MenuDVD Output TV StandardAudio Menu NtscDynamic Range Control Surround SoundAuto Calibration MenuRatings Menu Radio MenuStatus Menu MP3 and Jpeg Playback Menu Shuffle/Repeat MenuDTS Digital Surround Dolby SurroundMacrovision Progressive scan output at 525p and 625pSettings Navigation helpguideTaking care of your system KEF services Pre-programmed remote controlTrouble shooting Glossary Drive units SpecificationsInstrucciones en Español Información sobre seguridadPrecaución Configuración de las conexiones de vídeo DesembaladoAdvertencia Mandos del sistema de dvd Volume VolumenPantalla Panel posterior del DVD± Volume ± Volume Power Alimentación LED DE Modo DE Programación± SKIP/PRESET ± SALTAR/PRESINTONÍA STORE/ERASE Preset GUARDAR/BORRAR PresintoníaMenú de configuración Configuración del sistemaMenú Idioma Menú VídeoEstándar de TV Salida de DVDMenú Audio Sonido envolvente Control dinámico de rangoMenú Calibración Menú Radio Menú CalificacionesMenú Reproducción de MP3 y Jpeg Menú Mezclar/RepetirCódigos de región del dvd Barrido progresivo a 525 y 625 líneasCuidado del equipo Manual de ayuda de navegaciónControl remoto programado previamente Solución de problemas Glosario Unidades de altavoz EspecificacionesBrand of Teletext TV Remote control codesFrontech Magnavox Vexa Brand of TVBrand of VCR Brand of SAT Brand of Cable Brand of DVDBrand of CD Brand of HifiRemote control alternative keys functionality table KEF Audio UK KEF America Surround yourself with sound not speakers

KIT100 specifications

The KEF Audio KIT100 is a remarkable addition to the world of high-fidelity audio systems, designed to bring exceptional sound quality into the home environment. This innovative speaker system is a perfect blend of advanced engineering and elegant design, ensuring an immersive listening experience for audiophiles and casual listeners alike.

One of the standout features of the KIT100 is its unique Uni-Q driver array technology. This innovation places a 25mm tweeter at the acoustic center of a 130mm mid-bass driver, creating a single point source of sound. The result is a well-defined soundstage with remarkable imaging and clarity. Additionally, this design allows for a wider dispersion of sound, ensuring that listeners in different positions in the room can enjoy a consistent audio experience.

In terms of build quality, the KIT100 showcases KEF's commitment to craftsmanship. The cabinets are constructed from high-quality materials that minimize resonance, allowing the drivers to perform at their best. Available in several finishes, including walnut, black, and white, they seamlessly incorporate into any decor, making them not just audio equipment, but stylish home furnishings.

Another notable aspect of the KIT100 is its versatility. It is designed to pair perfectly with a variety of audio sources, from vinyl players to digital streaming devices. The inclusion of versatile connectivity options ensures compatibility with modern music systems, while the ability to handle both stereo and surround sound setups provides flexibility for different listening preferences.

The KIT100 also comes equipped with cutting-edge amplification technology. Each speaker features a built-in Class D amplifier, which provides a powerful and efficient performance that allows the system to deliver impressive dynamic range and control. This means that listeners can enjoy their favorite music genres, whether it’s classical, rock, or electronic, with fidelity to the artist's original intent.

In conclusion, the KEF Audio KIT100 is a sophisticated audio solution that combines unique technologies with high-quality materials and versatile functionality. With features like Uni-Q driver array technology, premium build quality, and advanced amplification, it stands out as an exceptional choice for anyone looking to enhance their home audio experience. Whether you are an audiophile or simply someone who appreciates great sound, the KIT100 promises to elevate your listening journey.
Top Page Image Contents