Porter-Cable H450CS, CH350CS, H650CS instruction manual To Start the Engine, Stopping Engine

Page 13

TO START THE ENGINE

Never run engine indoors or in enclosed, poor ventilated areas, engine exhaust contains carbon monoxide, an odorless and deadly gas.

1. Open the fuel shut-off valve on tank and engine.

2.Move the choke control located on the engine to "CHOKE" position.

STOPPING ENGINE

1.Disconnect all electrical loads.

2.Move the ON/OFF switch to "OFF" position.

3. Close fuel shut-off valves.

NOTE: No choke is required on warm engines. Make sure choke is in the "RUN" position on warm engine starts.

4.Move the ON/OFF switch on engine to the ON position.

5.Grasp handle on rope starter and pull slowly until resistance is felt. Let the rope rewind slowly. Pull rope with a rapid full arm stroke. Let rope rewind slowly. Repeat if necessary.

NOTE: IF ENGINE OIL LEVEL IS TOO LOW, ENGINE WILL NOT START. CHECK OIL LEVEL AND ADD IF NECESSARY.

6.When engine starts, gradually move the choke to the "RUN" position.

IMPORTANT: Allow generator to run at no load for 5 minutes upon each initial start-up to allow engine and generator to stabilize.

CONNECTING ELECTRICAL LOADS

1.Let engine run and warm up for five minutes after starting with no electrical load.

Connect loads in the following manner to prevent damage to equipment:

2.Connect inductive load equipment first, inductive loads consist of refrigerators, freezers, water pumps, air conditioners, or small hand tools. Connect the items that require the most wattage first. See Wattage Calculation Section in this manual.

3.Connect the lights next.

4.Voltage sensitive equipment should be the last equipment connected to the generator. Plug voltage sensitive appliances such at TV's, VCR's, micro- waves, ovens, computers, and cordless tele- phones into a UL listed voltage surge protector, then connect the UL listed voltage surge protector to the generator.

Failure to connect and operate equipment in this sequence can cause damage to equipment and will void the warranty on your generator.

Follow the wattage calculation table in the Wattage Calculation section of this manual. Overloading the generator will cause power fluctuations and can damage equipment and appliances.

Porter-Cable Corporation will only be respon- sible for damage to customer's equipment when the generator is determined to be defective. This determination will only be made by an authorized representative of Porter-Cable Corporation and this decision will be final. Porter-Cable Corporation reserves the right to inspect the electrical connections at the customer's site of operation and test the generator for proper operation before any determination of liability is made. Failure to maintain the equipment or wiring for inspection will void any claim for damages by the cus- tomer. Porter-Cable Corporation will not be responsible for equipment damaged as a result of voltage surges, improper operation or im- proper installation of the generator.

13 — ENG

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Instruction Manual Generators CH350CS SpecificationThis Warranty is not Transferable and does not Cover WarrantyImportant Safety Instructions Safety Guidelines DefinitionsHazard What could Happen HOW to Prevent IT Risk of Electrocution and FireWet, icy, or flooded conditions Operation of generator in rainDo not Operate Unit Risk of FireDoors or in ANY Confined AreaRisk of Breathing Inhalation Hazard Listed voltage surge protec Risk of Unsafe OperationGenerator Risk of Moving Parts Risk of HOT SurfacesRisk from Lifting Extension Cord Wire Gauge Chart Length AssemblyRemove Generator from Carton Grounding the GeneratorOperation Before Start UP To Start the Engine Connecting Electrical LoadsStopping Engine General Recommendations Engine Maintenance MaintenanceMaintenance Task Customer Responsibilities TableStorage Generator MaintenanceTo test Running Watts Starting Watts Wattage CalculationsVolts X Amp = Watts Volts x 10 amps = 1200 watts Starting Wattage RequirementsAppliance or Load Device Typical Device Wattage Total Household Wattage CalculatorProblem Cause Correction Troubleshooting GuideGenerator Quick Facts

CH350CS, H450CS, CH350CS, H650CS, CH350CS, H650CS specifications

The Porter-Cable H450CS, CH350CS, and H650CS are part of a renowned line of power tools designed for heavy-duty performance, catering to both professionals and DIY enthusiasts. These models deliver exceptional power and versatility, making them suitable for a diverse range of applications in woodworking, construction, and maintenance tasks.

The H450CS is an exceptional tool known for its lightweight design and robust performance. Featuring a powerful motor, it can handle various materials with ease, making it ideal for cutting, sanding, and shaping. The model’s ergonomic handle ensures comfort during extended use, while the quick-release blade mechanism allows for fast and easy blade changes. The H450CS also comes equipped with adjustable speed settings, allowing users to customize performance for different tasks, enhancing precision and control.

The CH350CS stands out with its impressive compactness and rugged construction. This model is designed for users who need a portable solution without compromising on power. The CH350CS features high-grade materials that ensure longevity and reliability, while its variable speed control provides adaptability for various applications. This tool excels in precise cuts and fine detail work, making it a favorite among carpenters and hobbyists alike. Additionally, it includes integrated dust management features, which enhance the user experience by minimizing cleanup.

The H650CS reflects the advanced technology that Porter-Cable is known for. This model includes innovative features such as an advanced motor cooling system that prolongs tool life by preventing overheating during extended use. Its heavy-duty construction makes it capable of handling tough jobs, while the user-friendly interface ensures that both beginners and experienced users can operate it effortlessly. The H650CS also incorporates safety features, including blade guards and anti-kickback mechanisms, providing added confidence for users during operation.

Overall, the Porter-Cable H450CS, CH350CS, and H650CS represent a top-tier selection of power tools. Their combination of advanced technologies, user-friendly designs, and high-quality construction makes them indispensable assets for professionals and DIY enthusiasts alike. Whether for intricate projects or substantial construction tasks, these models offer reliability and efficiency, positioning Porter-Cable as a leader in the power tool industry.
Top Page Image Contents