Porter-Cable Essential Porter Cable Manuals for Generator Operations and Maintenance
Page 20

Generator Quick Facts

CALL 1-888-559-8550 TO FIND A LOCAL AUTHORIZED SERVICE CENTER NEAR YOU FOR REPAIRS AND SERVICE PART PURCHASES

ENGINE

Use clean, fresh gasoline with a minimum 87 octane rating. Do not add gasoline

GAS

during or immediately after use.

 

 

ENGINE

Refer to engine owner's manual for oil recommendations.

 

OIL

Most generators are equipped with a low-oil shutdown. If the oil is low or if the

 

Generator is not level, the engine will not start.

 

 

WATTAGE

Make wattage calculations before use. Refer to general operator's manual for further

instructions.

 

 

 

WIRING

Contact an electrician for any wiring instructions. If wiring into a house, a double-throw

transfer switch and a heavy duty cord set must be used.

 

 

 

 

Use a standard (12V) lawn and garden battery with a minimum of 45 A.H. or 210 CCA.

 

 

BATTERY

The voltage and frequency are regulated by the rpm’s of the engine. Do not adjust the

throttle or governor to achieve higher performance. This will only alter the factory Pre-

VOLT

set settings and damage anything connected to the generator.

REG.

 

 

 

 

Be sure a volt/amp surge protector is used when sensitive electronic equipment is

 

used, such as: televisions, computers, stereos, and etc… The damage of such

 

equipment without the use of a protector WILL NOT be covered under warranty.

ENGINE

Do not adjust or attempt maintenance without consulting engine manual or an

authorized engine service center.

 

Add stabilizer to fuel tank and run engine for 5 minutes before storage.

STORAGE

When in long term storage, operate the generator every 60 days for at least 10 minutes

with a load on it. This will prevent the loss of residual magnetism that produces the

 

 

electricity.

 

Allow the generator to run 5 minutes at no load for the engine and the genhead to

 

stabilize.

OPERATION

Make sure the adequate size of extension cord is used. Refer to the Grounding

 

Instructions/Extension Cord section of the owners manual.

 

If the generator is operating equipment that is drawing half of the rated watts it is

 

considered 50% load. Using all of the rated watts is considered 100% load.

 

ALWAYS REFER TO THE MANUALS SUPPLIED WITH THIS UNIT

 

 

 

Porter-Cable Corporation

 

4825 Highway 45 North

 

P.O. Box 2468

 

Jackson, TN 38302-2468

 

1-888-559-8550

20 — ENG

Page 19 Page 20
Image 20
Page 19 Page 20
Contents Instruction Manual Generators Specification CH350CSWarranty This Warranty is not Transferable and does not CoverSafety Guidelines Definitions Important Safety InstructionsHazard What could Happen HOW to Prevent IT Risk of Electrocution and FireOperation of generator in rain Wet, icy, or flooded conditionsRisk of Fire Do not Operate UnitDoors or in ANY Confined AreaRisk of Breathing Inhalation Hazard Generator Risk of Unsafe OperationListed voltage surge protec Risk from Lifting Risk of HOT SurfacesRisk of Moving Parts Assembly Extension Cord Wire Gauge Chart LengthRemove Generator from Carton Grounding the GeneratorOperation Before Start UP Stopping Engine Connecting Electrical LoadsTo Start the Engine Maintenance General Recommendations Engine MaintenanceMaintenance Task Customer Responsibilities TableTo test Generator MaintenanceStorage Wattage Calculations Running Watts Starting WattsStarting Wattage Requirements Volts X Amp = Watts Volts x 10 amps = 1200 wattsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide Problem Cause CorrectionGenerator Quick Facts

CH350CS, H450CS, CH350CS, H650CS, CH350CS, H650CS specifications

The Porter-Cable H450CS, CH350CS, and H650CS are part of a renowned line of power tools designed for heavy-duty performance, catering to both professionals and DIY enthusiasts. These models deliver exceptional power and versatility, making them suitable for a diverse range of applications in woodworking, construction, and maintenance tasks.

The H450CS is an exceptional tool known for its lightweight design and robust performance. Featuring a powerful motor, it can handle various materials with ease, making it ideal for cutting, sanding, and shaping. The model’s ergonomic handle ensures comfort during extended use, while the quick-release blade mechanism allows for fast and easy blade changes. The H450CS also comes equipped with adjustable speed settings, allowing users to customize performance for different tasks, enhancing precision and control.

The CH350CS stands out with its impressive compactness and rugged construction. This model is designed for users who need a portable solution without compromising on power. The CH350CS features high-grade materials that ensure longevity and reliability, while its variable speed control provides adaptability for various applications. This tool excels in precise cuts and fine detail work, making it a favorite among carpenters and hobbyists alike. Additionally, it includes integrated dust management features, which enhance the user experience by minimizing cleanup.

The H650CS reflects the advanced technology that Porter-Cable is known for. This model includes innovative features such as an advanced motor cooling system that prolongs tool life by preventing overheating during extended use. Its heavy-duty construction makes it capable of handling tough jobs, while the user-friendly interface ensures that both beginners and experienced users can operate it effortlessly. The H650CS also incorporates safety features, including blade guards and anti-kickback mechanisms, providing added confidence for users during operation.

Overall, the Porter-Cable H450CS, CH350CS, and H650CS represent a top-tier selection of power tools. Their combination of advanced technologies, user-friendly designs, and high-quality construction makes them indispensable assets for professionals and DIY enthusiasts alike. Whether for intricate projects or substantial construction tasks, these models offer reliability and efficiency, positioning Porter-Cable as a leader in the power tool industry.
Top Page Image Contents