Poulan 189956, 271190 To Start Engine with a Weak Battery, To Adjust Steering Wheel ALIGN- Ment

Page 23

Engine

Pulley

Clutching

Idler

Stationary

Idler

Center Span

Keeper Transaxle

Pulley

00811

TO START ENGINE WITH A WEAK BATTERY

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Weak or Dead Battery

02614

Fully Charged

Battery

Washers

Retaining

Ring

Axle

Cover

Square Key

(Rear Wheel Only)

REPLACING BATTERY

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

23

Image 23
Contents Model no Table of Contents III. Children IV. ServiceWash hands after handling U1R Product SpecificationsCustomer Responsibilities API-SF-SJUnassembled Parts Unpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery HOW to SET UP Your TractorInstall Seat Check Brake System Check Tire PressureCheck for Proper Position of ALL Belts Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine ADD Gasoline To Start EngineMowing Tips Before Each USE General Recommendations Lubrication ChartTractor AIR Filter EngineSpark Plugs CleaningEngine Cooling System MufflerTo Remove Mower To Install MowerBelt Removal To Level Mower HousingSIDE-TO-SIDE Adjustment To Replace Mower Blade Drive BeltTo Check Brake Belt InstallationTo Check and Adjust Brake To Adjust BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BatteryTo Adjust Steering Wheel ALIGN- Ment Replacing BatteryTo Adjust Carburetor Engine OIL BatteryOther Fuel SystemProblem Cause Correction Troubleshooting ChartExcessive Mower blades will Tractor -- Model Number SchematicElectrical Repair PartsKEY Part Description Chassis and Enclosures 174620 Chassis 176554 Drawbar 155272 Ground Drive Bolt Hex 7/16-20 x 4 Gr -1.5 Thr Steering KEY Part NO. NO. Description Engine Optional Equipment Engine Seat Assembly Wheels and Tires DecalsLift Assembly Retainer Spring Mower Deck Screw Hex Thd Cut 1/4-20 x 1/2 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation

189956, 271190 specifications

The Poulan 189956,271190 is a standout product in the realm of outdoor power equipment, specifically designed for lawn care and maintenance. This model is known for its impressive combination of power, efficiency, and usability, making it an ideal choice for both homeowners and professional landscapers alike.

One of the primary features of the Poulan 189956,271190 is its robust engine. Typically equipped with a reliable two-cycle engine, this product delivers considerable power, making quick work of trimming and clearing yard debris. The engine’s design ensures efficient fuel consumption, allowing users to maximize their operational time without frequent refueling.

In terms of cutting performance, the Poulan 189956,271190 is engineered with a precision cutting system. This includes a high-quality cutting blade that guarantees clean cuts and effective trimming. The adjustable cutting height feature allows users to customize the cutting depth based on their specific lawn requirements, ensuring optimal results every time.

User comfort and convenience are also prioritized with this model. The ergonomic design provides a comfortable grip and reduced vibration, minimizing user fatigue during extended periods of operation. The lightweight construction of the equipment contributes to ease of handling, allowing for agile maneuvering around obstacles in the garden or lawn.

Technologically, the Poulan 189956,271190 incorporates innovations that enhance performance and durability. The air filtration system, for example, is designed to extend the lifespan of the engine by reducing dust and debris intake. Additionally, the easy-start mechanism simplifies the ignition process, enabling users to get started quickly without unnecessary hassle.

Safety features are another significant aspect of the Poulan 189956,271190. The model typically comes with a protective guard that shields operators from flying debris, while also providing a secure operating environment. The tool’s design includes safety switches and mechanisms that prevent accidental starting, ensuring a safe user experience.

In summary, the Poulan 189956,271190 is a reliable, efficient, and user-friendly option for outdoor maintenance. Its powerful engine, adjustable cutting features, ergonomic design, and safety mechanisms make it a preferred choice for anyone looking to maintain their garden or lawn effectively. With advanced technologies and thoughtful features, this model stands out in its category, delivering excellent performance whether for personal use or professional landscaping tasks.