Poulan 189956 To Level Mower Housing, SIDE-TO-SIDE Adjustment, To Replace Mower Blade Drive Belt

Page 21

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

Bottom edge of

Bottom edge of

mower to ground

mower to ground

 

00598

A

Ground Line

A

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2"

lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal num- ber of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

01268

Mandrel

“D” “D”

Both Front Links Should be Equal in Length

01267

Suspension Arm

01553

Lift Link Adjustment Nut

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side. If the following front-to-back adjust- ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of trac- tor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

Nut “F”

Nut “E”

 

Trunnion

 

Front Links

TO REPLACE MOWER BLADE DRIVE BELT

The mower blade drive belt may be re- placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1.Place attachment clutch in “DISEN- GAGED” position.

2.Move attachment lift lever forward to lower mower to its lowest position.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model no Table of Contents III. Children IV. ServiceWash hands after handling Customer Responsibilities Product SpecificationsAPI-SF-SJ U1RUnassembled Parts To Remove Tractor from Carton Tools Required for AssemblyBefore Removing Tractor from Skid Unpack CartonHOW to SET UP Your Tractor Install SeatCheck Battery Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine ADD Gasoline To Start EngineMowing Tips Before Each USE General Recommendations Lubrication ChartTractor AIR Filter EngineEngine Cooling System CleaningMuffler Spark PlugsTo Remove Mower To Install MowerSIDE-TO-SIDE Adjustment To Level Mower HousingTo Replace Mower Blade Drive Belt Belt RemovalTo Check and Adjust Brake Belt InstallationTo Adjust Brake To Check BrakeTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak BatteryReplacing Battery Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Other BatteryFuel System Engine OILProblem Cause Correction Troubleshooting ChartExcessive Mower blades will Tractor -- Model Number SchematicElectrical Repair PartsKEY Part Description Chassis and Enclosures 174620 Chassis 176554 Drawbar 155272 Ground Drive Bolt Hex 7/16-20 x 4 Gr -1.5 Thr Steering KEY Part NO. NO. Description Engine Optional Equipment Engine Seat Assembly Wheels and Tires DecalsLift Assembly Retainer Spring Mower Deck Screw Hex Thd Cut 1/4-20 x 1/2 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation

189956, 271190 specifications

The Poulan 189956,271190 is a standout product in the realm of outdoor power equipment, specifically designed for lawn care and maintenance. This model is known for its impressive combination of power, efficiency, and usability, making it an ideal choice for both homeowners and professional landscapers alike.

One of the primary features of the Poulan 189956,271190 is its robust engine. Typically equipped with a reliable two-cycle engine, this product delivers considerable power, making quick work of trimming and clearing yard debris. The engine’s design ensures efficient fuel consumption, allowing users to maximize their operational time without frequent refueling.

In terms of cutting performance, the Poulan 189956,271190 is engineered with a precision cutting system. This includes a high-quality cutting blade that guarantees clean cuts and effective trimming. The adjustable cutting height feature allows users to customize the cutting depth based on their specific lawn requirements, ensuring optimal results every time.

User comfort and convenience are also prioritized with this model. The ergonomic design provides a comfortable grip and reduced vibration, minimizing user fatigue during extended periods of operation. The lightweight construction of the equipment contributes to ease of handling, allowing for agile maneuvering around obstacles in the garden or lawn.

Technologically, the Poulan 189956,271190 incorporates innovations that enhance performance and durability. The air filtration system, for example, is designed to extend the lifespan of the engine by reducing dust and debris intake. Additionally, the easy-start mechanism simplifies the ignition process, enabling users to get started quickly without unnecessary hassle.

Safety features are another significant aspect of the Poulan 189956,271190. The model typically comes with a protective guard that shields operators from flying debris, while also providing a secure operating environment. The tool’s design includes safety switches and mechanisms that prevent accidental starting, ensuring a safe user experience.

In summary, the Poulan 189956,271190 is a reliable, efficient, and user-friendly option for outdoor maintenance. Its powerful engine, adjustable cutting features, ergonomic design, and safety mechanisms make it a preferred choice for anyone looking to maintain their garden or lawn effectively. With advanced technologies and thoughtful features, this model stands out in its category, delivering excellent performance whether for personal use or professional landscaping tasks.
Top Page Image Contents