Poulan 195806 manual Cleaning

Page 19

MAINTENANCE

After oil has drained completely, close the drain valve turning clockwise. Use the 7/16" (11mm) wrench to apply a small amount of torque to keep it closed. Do not over tighten.

Remove the drain tube and store in a safe place.

Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this man- ual.

Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.Tighten cap onto the tube securely when finished.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

AIR FILTER

Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See Engine Manual.

ENGINE OIL FILTER

Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year.

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 18)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

With engine cool, remove filter and plug fuel line sec- tions.

Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

Be sure there are no fuel line leaks and clamps are properly positioned.

Immediately wipe up any spilled gasoline.

CLAMP

CLAMP

FUEL FILTER

FIG. 18

CLEANING

Clean engine, battery, seat, finish, etc. of all foreign matter.

Keep finished surfaces and wheels free of all gasoline, oil, etc.

Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

19

Image 19
Contents Always Wear EYE Protection During Operation ModelGeneral Operation Safe Operation Practices for Ride-On MowersII. Slope Operation IV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt SeesCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Height Adjustment Knob Used to adjust the mower heightHOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceService Dates Lubrication ChartBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower HousingFRONT-TO-BACK Adjustment See Figs Belt Routing Mower Drive Belt InstallationTo Replace Mower Drive Belt See Fig Mower Drive Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Attachment Clutch See FigTo Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigTo Remove Wheel for Repairs To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERInterlocks and Relays To Adjust Throttle Control CableTo Adjust Choke Control To Adjust Carburetor To Replace Headlight BulbCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

195806 specifications

The Poulan 195806 is a high-performance chainsaw designed for both professional and amateur users. It stands out with its robust construction and advanced features, making it a preferred choice for those looking to tackle a variety of cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 195806 is its powerful engine. It is equipped with a reliable two-stroke engine that delivers substantial power, ensuring efficient operation even under heavy loads. The engine is designed for smooth starts and steady performance, which is crucial when dealing with demanding cutting jobs.

Another notable characteristic is its lightweight design. Weighing in at a manageable amount, the Poulan 195806 is easy to maneuver, reducing user fatigue during extended use. This makes it an excellent option for homeowners who may need to use a chainsaw for longer periods without experiencing discomfort.

The chainsaw also emphasizes safety, featuring an automatic chain brake that engages during kickback situations. This helps protect the user from potential injuries, making the chainsaw a safer option for those who may not have extensive experience with power tools. Additionally, an ergonomically designed handle provides a comfortable grip, allowing for precise control while cutting.

The Poulan 195806 utilizes advanced technologies such as the OxyPower engine, which optimizes fuel efficiency while producing fewer emissions. This environmentally friendly approach appeals to users concerned about sustainability. The chainsaw's quick-release air filter is another innovative feature, allowing for easy maintenance and ensuring longevity while maximizing performance.

Additionally, a tool-less chain tensioning system simplifies the process of adjusting the chain, ensuring the chainsaw delivers optimal cutting performance without requiring extensive technical knowledge. This feature is particularly beneficial for inexperienced users who may find traditional tensioning systems cumbersome.

In terms of versatility, the Poulan 195806 is compatible with various bar lengths, allowing users to customize the chainsaw to their specific needs, whether they require precision for trimming or additional power for larger tasks.

Overall, the Poulan 195806 combines power, safety, and user-friendly features in a compact design, making it an excellent choice for those seeking a reliable and efficient chainsaw for their cutting needs. Its blend of advanced technologies and characteristics positions it as a valuable tool in any toolkit, ready to tackle a variety of outdoor tasks with ease.