Poulan 195806 manual To Attach Nose Roller See Fig, Install Mower and Drive Belt Sees

Page 8

ASSEMBLY

TO ATTACH NOSE ROLLER (See Fig. 6)

•Assemble brackets "A" and "B" to the inside of mower mounting brackets as shown. Tighten securely.

NOTE: Be sure bracket tabs are positioned in tab holes in mower brackets.

•Position nose roller between brackets and install rod and retainer spring.

HEX BOLT

LOCK

NUT

ROD

"B"

TABBRACKET HOLE

NOSE

 

02612

ROLLER

"A" BRACKET

 

RETAINER SPRING

 

 

 

FIG. 6

INSTALL MOWER AND DRIVE BELT (Sees Fig. 7 and 8)

See MOWER AND DRIVE BELT ASSEMBLY Supplement Sheet for additional guidance on this assembly.

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage park- ing brake.

•Turn steering wheel to the left as far as it will go and position mower on right side of tractor with deflector

shield to the right.

•Remove plastic tie strap from mower belt and check belt for proper routing in all mower pulley grooves.

•Slide mower under tractor until it is centered under trac- tor. DO NOT connect any pins.When properly centered the front mower brackets should be aligned so when the front suspension plate is lowered it should slide between the mower brackets.

•Lower attachment lift lever to lowest position.

•Cut plastic tie and lower front suspension plate.

•ATTACH FRONT PLATE - From left side of mower, posi- tion front plate assembly between front mower brackets, align holes, position flanged pin notch horizontally and insert the pin all the way. The notch is in line with the hole in pin.

•Secure pin with double loop retainer spring between the plate and mower bracket.If necessary, move mower side-to-side to give space between plate and mower bracket.

•Go to right hand side of mower and insert pin and retainer spring in the same manner.

•CONNECT REAR PINS - Connect right hand side first. Pull out and hold the spring loaded pin, align hole in suspension arm and release pin. Be sure pin returns to fully seated position and is attached to the suspension arm.

•Go to left side of mower and connect rear pin in the same manner.

•Disengage belt tension rod.

•From right side of tractor, install belt onto engine clutch pulley.

LOCKING BRACKET

 

 

BELT TENSION

 

ELECTRIC CLUTCH PULLEY

ROD

SUSPENSION ARMS

DISENGAGED

 

FRONT PLATE ASSEMBLY

POSITION

 

 

 

 

 

FRONT MOWER

 

 

BRACKET

GAUGE

 

DOUBLE LOOP

 

RETAINER SPRINGS

WHEEL

 

 

 

 

FLANGED PIN -

 

 

POSITION NOTCH

 

 

HORIZONTALLY

REAR MOWER PINS

02

786

 

 

 

 

DEFLECTOR SHIELD

FIG. 7

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model Always Wear EYE Protection During OperationII. Slope Operation Safe Operation Practices for Ride-On MowersGeneral Operation Service General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig Assemble Gauge Wheels to Mower Deck SeeInstall Mower and Drive Belt Sees To Attach Nose Roller See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance Service DatesLubrication Chart General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning Service and Adjustments To Install MowerTo Level Mower Housing To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs Mower Drive Belt Installation To Replace Mower Drive Belt See FigMower Drive Belt Removal Belt RoutingTo Adjust Attachment Clutch See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight Bulb Interlocks and RelaysOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195806 specifications

The Poulan 195806 is a high-performance chainsaw designed for both professional and amateur users. It stands out with its robust construction and advanced features, making it a preferred choice for those looking to tackle a variety of cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 195806 is its powerful engine. It is equipped with a reliable two-stroke engine that delivers substantial power, ensuring efficient operation even under heavy loads. The engine is designed for smooth starts and steady performance, which is crucial when dealing with demanding cutting jobs.

Another notable characteristic is its lightweight design. Weighing in at a manageable amount, the Poulan 195806 is easy to maneuver, reducing user fatigue during extended use. This makes it an excellent option for homeowners who may need to use a chainsaw for longer periods without experiencing discomfort.

The chainsaw also emphasizes safety, featuring an automatic chain brake that engages during kickback situations. This helps protect the user from potential injuries, making the chainsaw a safer option for those who may not have extensive experience with power tools. Additionally, an ergonomically designed handle provides a comfortable grip, allowing for precise control while cutting.

The Poulan 195806 utilizes advanced technologies such as the OxyPower engine, which optimizes fuel efficiency while producing fewer emissions. This environmentally friendly approach appeals to users concerned about sustainability. The chainsaw's quick-release air filter is another innovative feature, allowing for easy maintenance and ensuring longevity while maximizing performance.

Additionally, a tool-less chain tensioning system simplifies the process of adjusting the chain, ensuring the chainsaw delivers optimal cutting performance without requiring extensive technical knowledge. This feature is particularly beneficial for inexperienced users who may find traditional tensioning systems cumbersome.

In terms of versatility, the Poulan 195806 is compatible with various bar lengths, allowing users to customize the chainsaw to their specific needs, whether they require precision for trimming or additional power for larger tasks.

Overall, the Poulan 195806 combines power, safety, and user-friendly features in a compact design, making it an excellent choice for those seeking a reliable and efficient chainsaw for their cutting needs. Its blend of advanced technologies and characteristics positions it as a valuable tool in any toolkit, ready to tackle a variety of outdoor tasks with ease.
Top Page Image Contents