Poulan 195806 manual To Adjust Attachment Clutch See Fig, To Check and Adjust Brake

Page 23

SERVICE AND ADJUSTMENTS

TO ADJUST ATTACHMENT CLUTCH (See Fig. 25)

The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required. Adjustments should be made by your nearest authorized service center/department.

Make sure attachment clutch and ignition switches are in “OFF” position.

Adjust the three nylon locknuts until space between clutch plate and rotor measures .012" at all three slot locations cut in side of brake plate.

NOTE: After installing a new electric clutch, run tractor at full throttle and engage and disengage electric clutch 10 cycles to wear in clutch plate.

ROTOR

 

 

 

 

00751

SLOT (3)

CLUTCH PLATE

.012"

 

 

NYLON LOCKNUT (3)

 

BRAKE PLATE

FIG. 25

TO CHECK AND ADJUST BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE/REPLACE PADS

Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 26)

Park the tractor on level surface. Engage parking brake. For ease of service there is a belt installation guide decal on bottom of left footrest.

Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

BELT REMOVAL -

Create slack in belt by removing retainer spring from drive belt tension handle.

Remove belt from all idler pulleys, transaxle pulley and then from engine pulley.

BELT INSTALLATION -

Install new belt around engine pulley first, then around transaxle pulley and lastly into all the idler pulleys.

Check to be sure belt is positioned correctly and is on proper side of all belt keepers.

Engage the drive belt tension handle and replace the retainer spring.

Reinstall mower.

 

 

 

 

RETAINER

 

 

 

 

 

SPRING

 

 

 

 

 

DRIVE BELT

 

 

 

 

 

TENSION HANDLE

 

 

02504

 

 

 

 

 

 

 

ENGINE PULLEY

 

 

TRANSAXLE

 

BELT KEEPER

 

PULLEY

 

 

 

 

 

 

 

FLAT IDLER

 

 

 

 

 

 

BELT

 

BELT

BELT

 

2498

KEEPER

 

KEEPER

 

 

 

 

CLUTCHING

CLUTCHING

 

V-IDLER

KEEPER

 

 

 

IDLER

FLAT IDLER

 

 

 

 

FIG. 26

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 27)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Park tractor on level surface. Stop tractor by turning ignition key to “OFF” position and engage parking brake.

Loosen the adjustment bolt in front of the right rear wheel.

Move motion control lever to the neutral position (N).

Tighten the adjustment bolt.

ADJUSTMENT

BOLT

02508

FIG. 27

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

23

Image 23
Contents Always Wear EYE Protection During Operation ModelII. Slope Operation Safe Operation Practices for Ride-On MowersGeneral Operation IV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt SeesCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Height Adjustment Knob Used to adjust the mower heightHOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission General Recommendations MaintenanceService Dates Lubrication ChartTo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower HousingFRONT-TO-BACK Adjustment See Figs Belt Routing Mower Drive Belt InstallationTo Replace Mower Drive Belt See Fig Mower Drive Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Attachment Clutch See FigTo Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigTo Remove Wheel for Repairs To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERInterlocks and Relays To Adjust Throttle Control CableTo Adjust Choke Control To Adjust Carburetor To Replace Headlight BulbCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

195806 specifications

The Poulan 195806 is a high-performance chainsaw designed for both professional and amateur users. It stands out with its robust construction and advanced features, making it a preferred choice for those looking to tackle a variety of cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 195806 is its powerful engine. It is equipped with a reliable two-stroke engine that delivers substantial power, ensuring efficient operation even under heavy loads. The engine is designed for smooth starts and steady performance, which is crucial when dealing with demanding cutting jobs.

Another notable characteristic is its lightweight design. Weighing in at a manageable amount, the Poulan 195806 is easy to maneuver, reducing user fatigue during extended use. This makes it an excellent option for homeowners who may need to use a chainsaw for longer periods without experiencing discomfort.

The chainsaw also emphasizes safety, featuring an automatic chain brake that engages during kickback situations. This helps protect the user from potential injuries, making the chainsaw a safer option for those who may not have extensive experience with power tools. Additionally, an ergonomically designed handle provides a comfortable grip, allowing for precise control while cutting.

The Poulan 195806 utilizes advanced technologies such as the OxyPower engine, which optimizes fuel efficiency while producing fewer emissions. This environmentally friendly approach appeals to users concerned about sustainability. The chainsaw's quick-release air filter is another innovative feature, allowing for easy maintenance and ensuring longevity while maximizing performance.

Additionally, a tool-less chain tensioning system simplifies the process of adjusting the chain, ensuring the chainsaw delivers optimal cutting performance without requiring extensive technical knowledge. This feature is particularly beneficial for inexperienced users who may find traditional tensioning systems cumbersome.

In terms of versatility, the Poulan 195806 is compatible with various bar lengths, allowing users to customize the chainsaw to their specific needs, whether they require precision for trimming or additional power for larger tasks.

Overall, the Poulan 195806 combines power, safety, and user-friendly features in a compact design, making it an excellent choice for those seeking a reliable and efficient chainsaw for their cutting needs. Its blend of advanced technologies and characteristics positions it as a valuable tool in any toolkit, ready to tackle a variety of outdoor tasks with ease.