Poulan 195806 manual Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

(1)

Tire pressure gauge

(1)

9/16" wrench

(1)

Utility knife

(2)

1/2" wrenches

(1)

Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Remove mower and packing materials.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

•Remove locknut and large flat washer from steering shaft.

•Position front wheels of the tractor so they are pointing straight forward.

•Slide the steering sleeve over the steering shaft.

•Position steering wheel so cross bars are horizontal (left to right) and slide onto steering wheel adapter.

•Secure steering wheel to steering shaft with locknut and large flat washer previously removed. Tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

STEERING WHEEL

INSERT

LOCK NUT

LARGE FLAT WASHER

STEERING WHEEL

STEERING WHEEL ADAP- TOR

STEERING

SHAFT

STEERING

SLEEVE

 

 

 

8

 

 

1

 

8

 

2

 

 

0

 

 

 

FIG. 1

CHECK BATTERY (See Fig. 2)

•Lift hood to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

LABEL

02173

FIG. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model Always Wear EYE Protection During OperationSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation III. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Assemble Gauge Wheels to Mower Deck SeeInstall Mower and Drive Belt Sees To Attach Nose Roller See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigUsing the Reverse Operation System Reverse Operation System ROSCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Lubrication Chart MaintenanceService Dates General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs Mower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Drive Belt See Fig Belt RoutingTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Attachment Clutch See FigTo Check and Adjust Brake Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig To Remove Wheel for RepairsTo Adjust Carburetor To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control Interlocks and RelaysEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195806 specifications

The Poulan 195806 is a high-performance chainsaw designed for both professional and amateur users. It stands out with its robust construction and advanced features, making it a preferred choice for those looking to tackle a variety of cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 195806 is its powerful engine. It is equipped with a reliable two-stroke engine that delivers substantial power, ensuring efficient operation even under heavy loads. The engine is designed for smooth starts and steady performance, which is crucial when dealing with demanding cutting jobs.

Another notable characteristic is its lightweight design. Weighing in at a manageable amount, the Poulan 195806 is easy to maneuver, reducing user fatigue during extended use. This makes it an excellent option for homeowners who may need to use a chainsaw for longer periods without experiencing discomfort.

The chainsaw also emphasizes safety, featuring an automatic chain brake that engages during kickback situations. This helps protect the user from potential injuries, making the chainsaw a safer option for those who may not have extensive experience with power tools. Additionally, an ergonomically designed handle provides a comfortable grip, allowing for precise control while cutting.

The Poulan 195806 utilizes advanced technologies such as the OxyPower engine, which optimizes fuel efficiency while producing fewer emissions. This environmentally friendly approach appeals to users concerned about sustainability. The chainsaw's quick-release air filter is another innovative feature, allowing for easy maintenance and ensuring longevity while maximizing performance.

Additionally, a tool-less chain tensioning system simplifies the process of adjusting the chain, ensuring the chainsaw delivers optimal cutting performance without requiring extensive technical knowledge. This feature is particularly beneficial for inexperienced users who may find traditional tensioning systems cumbersome.

In terms of versatility, the Poulan 195806 is compatible with various bar lengths, allowing users to customize the chainsaw to their specific needs, whether they require precision for trimming or additional power for larger tasks.

Overall, the Poulan 195806 combines power, safety, and user-friendly features in a compact design, making it an excellent choice for those seeking a reliable and efficient chainsaw for their cutting needs. Its blend of advanced technologies and characteristics positions it as a valuable tool in any toolkit, ready to tackle a variety of outdoor tasks with ease.
Top Page Image Contents