Poulan 195806 manual FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

00598

GROUND

 

 

A

GROUND LINE

A

 

 

FIG. 20

SUSPENSION

ARM

01553

LIFT LINK

ADJUSTMENT NUT

FIG. 21

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

02548

BLADE

“B”“B”

FIG. 22

BOTH FRONT PLATE LINKS MUST BE

EQUAL IN LENGTH

02516

NUT “D”

 

NUT “C”

 

02517

TRUNNION

 

 

FRONT PLATE

 

 

ASSEMBLY

 

 

FIG. 23

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Always Wear EYE Protection During Operation ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation General Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt SeesCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Height Adjustment Knob Used to adjust the mower heightHOW to USE Your Tractor Using the Reverse Operation System To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Service Dates MaintenanceLubrication Chart General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning To Install Mower Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal Belt RoutingTo Check and Adjust Brake To Adjust Attachment Clutch See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight Bulb Interlocks and RelaysFuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

195806 specifications

The Poulan 195806 is a high-performance chainsaw designed for both professional and amateur users. It stands out with its robust construction and advanced features, making it a preferred choice for those looking to tackle a variety of cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 195806 is its powerful engine. It is equipped with a reliable two-stroke engine that delivers substantial power, ensuring efficient operation even under heavy loads. The engine is designed for smooth starts and steady performance, which is crucial when dealing with demanding cutting jobs.

Another notable characteristic is its lightweight design. Weighing in at a manageable amount, the Poulan 195806 is easy to maneuver, reducing user fatigue during extended use. This makes it an excellent option for homeowners who may need to use a chainsaw for longer periods without experiencing discomfort.

The chainsaw also emphasizes safety, featuring an automatic chain brake that engages during kickback situations. This helps protect the user from potential injuries, making the chainsaw a safer option for those who may not have extensive experience with power tools. Additionally, an ergonomically designed handle provides a comfortable grip, allowing for precise control while cutting.

The Poulan 195806 utilizes advanced technologies such as the OxyPower engine, which optimizes fuel efficiency while producing fewer emissions. This environmentally friendly approach appeals to users concerned about sustainability. The chainsaw's quick-release air filter is another innovative feature, allowing for easy maintenance and ensuring longevity while maximizing performance.

Additionally, a tool-less chain tensioning system simplifies the process of adjusting the chain, ensuring the chainsaw delivers optimal cutting performance without requiring extensive technical knowledge. This feature is particularly beneficial for inexperienced users who may find traditional tensioning systems cumbersome.

In terms of versatility, the Poulan 195806 is compatible with various bar lengths, allowing users to customize the chainsaw to their specific needs, whether they require precision for trimming or additional power for larger tasks.

Overall, the Poulan 195806 combines power, safety, and user-friendly features in a compact design, making it an excellent choice for those seeking a reliable and efficient chainsaw for their cutting needs. Its blend of advanced technologies and characteristics positions it as a valuable tool in any toolkit, ready to tackle a variety of outdoor tasks with ease.
Top Page Image Contents