Poulan 195806 manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

Page 24

SERVICE AND ADJUSTMENTS

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

FRONT WHEEL (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal.

•Repair tire and reassemble.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

REAR WHEEL -

•Block rear axle securely.

•Remove five (5) hub bolts to allow wheel removal.

•Repair tire and reassemble. Replace and tighten hub bolts securely.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE

COVER

 

q

s

3

 

0066

 

FIG. 28

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

 

02614

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 29

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model Always Wear EYE Protection During OperationSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig Assemble Gauge Wheels to Mower Deck SeeInstall Mower and Drive Belt Sees To Attach Nose Roller See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance Service DatesLubrication Chart General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install MowerTo Level Mower Housing To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs Mower Drive Belt Installation To Replace Mower Drive Belt See FigMower Drive Belt Removal Belt RoutingTo Adjust Attachment Clutch See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight Bulb Interlocks and RelaysOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195806 specifications

The Poulan 195806 is a high-performance chainsaw designed for both professional and amateur users. It stands out with its robust construction and advanced features, making it a preferred choice for those looking to tackle a variety of cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 195806 is its powerful engine. It is equipped with a reliable two-stroke engine that delivers substantial power, ensuring efficient operation even under heavy loads. The engine is designed for smooth starts and steady performance, which is crucial when dealing with demanding cutting jobs.

Another notable characteristic is its lightweight design. Weighing in at a manageable amount, the Poulan 195806 is easy to maneuver, reducing user fatigue during extended use. This makes it an excellent option for homeowners who may need to use a chainsaw for longer periods without experiencing discomfort.

The chainsaw also emphasizes safety, featuring an automatic chain brake that engages during kickback situations. This helps protect the user from potential injuries, making the chainsaw a safer option for those who may not have extensive experience with power tools. Additionally, an ergonomically designed handle provides a comfortable grip, allowing for precise control while cutting.

The Poulan 195806 utilizes advanced technologies such as the OxyPower engine, which optimizes fuel efficiency while producing fewer emissions. This environmentally friendly approach appeals to users concerned about sustainability. The chainsaw's quick-release air filter is another innovative feature, allowing for easy maintenance and ensuring longevity while maximizing performance.

Additionally, a tool-less chain tensioning system simplifies the process of adjusting the chain, ensuring the chainsaw delivers optimal cutting performance without requiring extensive technical knowledge. This feature is particularly beneficial for inexperienced users who may find traditional tensioning systems cumbersome.

In terms of versatility, the Poulan 195806 is compatible with various bar lengths, allowing users to customize the chainsaw to their specific needs, whether they require precision for trimming or additional power for larger tasks.

Overall, the Poulan 195806 combines power, safety, and user-friendly features in a compact design, making it an excellent choice for those seeking a reliable and efficient chainsaw for their cutting needs. Its blend of advanced technologies and characteristics positions it as a valuable tool in any toolkit, ready to tackle a variety of outdoor tasks with ease.
Top Page Image Contents