Poulan 96042004201, 411274 manual To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 15)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Roll belt off engine pulley (M) and belt keepers (G).

•Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

•Remove clutch cable spring (Q) from idler arm (R).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: AFTER REAR LIFT LINKS

ARE DISCONNECTED, THE ATTACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HAVE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

•Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE

MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Fig. 16–19)

Be sure tractor is on level surface and engage parking brake.

•Lower attachment lift lever to it's lowest position.

CAUTION: LIFT LEVER IS SPRING

LOADED. HAVE A TIGHT GRIP ON

LIFT LEVER, LOWER IT SLOWLY AND

ENGAGE IN LOWEST POSITION.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

•Slide mower under tractor until it is centered under tractor.

•ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring.

•Repeat on opposite side of tractor.

G MF

Q R

G

P

A E

B

C

K

D

 

L

FIG. 15

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model PB20H46LTGeneral Operation Safe Operation Practices for Ride-On MowersII. Slope Operation III. Children ServiceIV. Towing Table of Contents Contents of Hardware Pack Unpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsRunning Mowing TipsPurge Transmission Automatic Transmission Warm UPMaintenance Check Operator Presence System TractorBlade Removal See Fig To Sharpen Blade See FigTransaxle Cooling BatteryEngine BeltsCleaning To Remove Mower See Fig To Install Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Replace Motion Belt Drive See Fig Belt InstallationTo Replace Mower Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Page Page UNE Pliez EST Ceci Degrés Suivant LESLimitée Garantie Défectueux est Dépannage DE GuideRalenti Moteur DU Commande LA Régler PourGAZ DES Commande EntreposageRéglages ET Révision LA DE L’ALIGNEMENT Régler Pour CarrossageAVANT/ Roues DES Convergence Tionrecdi25 .FIG Courroie Acer Rempl Pour’ENTRAÎNEMENT Freins LES Vérifier Pour20 .FIG Tondeuse LA Niveau LE Ajuster Pour22 .FIG 21 .FIG18 .FIG 19 .FIG 17 .FIG16 .FIG Fig Voir Courroie LA ET Tondeuse LA InstallerReglages ET Revision TracteurAIR À Filtre Ligne EN Installé D’ESSENCE FiltreEntretien ’ALLUMAGE BougieLubrification Transmission LA DE RefroidissementTrapézoïdales Courroies Fig la Voir Lame LA Enlever Fig la Voir Lame LA AffilerEN Fonctionnement DE Système ET Utilisation Chaque Avant O I T a D N a M M O C E RGénérales Lubrification DE TableauQueti UtilisationTransmission LA Purger Tonte DE ConseilsMoteur LE Démarrer DE Avant Tondeuse DE Lames LES Arrêter Pour MAR EN Fonctionnement DE SystèmeTondeuse LA Utiliser Pour ROS Arrière CHETionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Fig la Voir MentneTracteur Votre Connaissez Propriété la de lendommagement Correctement Sont Courroies LES MontageToutes SI Vérifier Toutes SI Vérifier Desmancom des tionfonc la et Fig la Voir Batterie LA VérifierLA DE Tracteur LE Retirer Pour LE Pour Exigés Outils LES DU Tracteur LE Sortir PourMontar SIN Piezas Client DU Responsabilités SommaireProduit DE Spécifications Général Entretien EntretienRemorquage EnfantsTracteurs des sécurité toute en l’utilisation pour Conseils PentesLES Dans Fonctionnement Général FonctionnementAUX Imprimé

96042004201, 411274 specifications

The Poulan 411274,96042004201 is a robust and efficient replacement chain designed for various outdoor power equipment, specifically chainsaws. This chainsaw chain is recognized for its remarkable performance and durability, making it a popular choice among both amateur and professional users.

One of the standout features of the Poulan 411274 is its construction. Made from high-quality steel, it is engineered to withstand intense usage while delivering exceptional cutting performance. The sharpness of the teeth, combined with their design, enables smoother and quicker cuts, reducing the effort needed during operation.

The chain features a 3/8 inch pitch, which strikes an excellent balance between cutting speed and control. This pitch size is often favored for medium to large-sized chainsaws, providing a powerful cutting ability suitable for various tasks such as tree trimming, firewood cutting, and other light to medium forestry work.

An essential characteristic of the Poulan 411274 is its low kickback design. This feature is vital for user safety, as it minimizes the risk of kickback accidents, which can occur when the chain suddenly jerks back towards the user during cutting. The chain also incorporates a special heat treatment process that enhances its strength and wear resistance, ensuring it maintains its cutting edge longer and requires fewer replacements over time.

The technology behind the chain includes precision-engineered cutting teeth that significantly improve cutting efficiency. This design not only enhances performance but also reduces the amount of force required from the operator, thereby decreasing fatigue during prolonged use.

Ease of installation is another notable aspect of the Poulan 411274. It is designed to fit various Poulan chainsaw models as well as compatible devices, making it a versatile choice for users. The chain comes with pre-stretched links, ensuring it fits snugly without the need for extensive adjustments, allowing users to get back to work quickly.

Overall, the Poulan 411274,96042004201 chain combines durability, safety, and efficiency, making it an essential component for anyone looking to enhance their outdoor cutting tasks. Whether you're a weekend warrior or a professional in the field, this chain provides the reliability and performance needed for effective chainsaw operation.
Top Page Image Contents