Poulan 411274, 96042004201 manual Troubleshooting Points, Problem Cause Correction

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

4.

Bad spark plug.

4.

Replace spark plug.

 

5.

Dirty air filter.

5.

Clean/replace air filter.

 

6.

Dirty fuel filter.

6.

Replace fuel filter.

 

7.

Water in fuel.

7.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

8.

Loose or damaged wiring.

8.

Check all wiring.

 

9.

Carburetor out of adjustment.

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

10.

Engine valves out of adjustment.

10.

Contact an authorized service center/department.

 

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

2.

Bad spark plug.

2.

Replace spark plug.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

5.

Stale or dirty fuel.

5.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine will not turn over

1.

Clutch/brake pedal not depressed.

1.

Depress clutch/brake pedal.

 

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Blown fuse.

4.

Replace fuse.

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine clicks but will not

1.

Weak or dead battery.

1.

Recharge or replace battery.

start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Raise cutting height/reduce speed.

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

3.

Build-up of grass, leaves and trash under mower.

3.

Clean underside of mower housing.

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

8.

Stale or dirty fuel.

8.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

9.

Water in fuel.

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

 

Excessive vibration

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents PB20H46LT ModelII. Slope Operation Safe Operation Practices for Ride-On MowersGeneral Operation IV. Towing ServiceIII. Children Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemReverse Operation System ROS To Operate Mower See FigTowing Carts and Other ATTACH- Ments Before Starting the EngineTo Transport Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission RunningMaintenance To Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemBelts BatteryEngine Transaxle CoolingCleaning To Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Drive Belt See Fig To Replace Motion Belt Drive See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Page Page Degrés Suivant LES UNE Pliez EST CeciLimitée Garantie Dépannage DE Guide Défectueux estRalenti Entreposage DU Commande LA Régler PourGAZ DES Commande MoteurRéglages ET Révision Tionrecdi CarrossageAVANT/ Roues DES Convergence LA DE L’ALIGNEMENT Régler PourFreins LES Vérifier Pour Courroie Acer Rempl Pour’ENTRAÎNEMENT 25 .FIG21 .FIG Tondeuse LA Niveau LE Ajuster Pour22 .FIG 20 .FIG16 .FIG 19 .FIG 17 .FIG18 .FIG Tracteur Courroie LA ET Tondeuse LA InstallerReglages ET Revision Fig Voir’ALLUMAGE Bougie Ligne EN Installé D’ESSENCE FiltreEntretien AIR À FiltreTrapézoïdales Courroies Transmission LA DE RefroidissementLubrification EN Fonctionnement DE Système ET Fig la Voir Lame LA AffilerFig la Voir Lame LA Enlever Lubrification DE Tableau O I T a D N a M M O C E RGénérales Utilisation Chaque AvantTonte DE Conseils UtilisationTransmission LA Purger QuetiMoteur LE Démarrer DE Avant ROS Arrière CHE MAR EN Fonctionnement DE SystèmeTondeuse LA Utiliser Pour Tondeuse DE Lames LES Arrêter PourFig la Voir Mentne GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Tionsta DE Frein LE Engager PourTracteur Votre Connaissez Propriété la de lendommagement Toutes SI Vérifier Toutes SI Vérifier MontageCorrectement Sont Courroies LES LA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA VérifierDesmancom des tionfonc la et DU Tracteur LE Sortir Pour LE Pour Exigés Outils LESMontar SIN Piezas Produit DE Spécifications SommaireClient DU Responsabilités Enfants EntretienRemorquage Général EntretienGénéral Fonctionnement PentesLES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAUX Imprimé

96042004201, 411274 specifications

The Poulan 411274,96042004201 is a robust and efficient replacement chain designed for various outdoor power equipment, specifically chainsaws. This chainsaw chain is recognized for its remarkable performance and durability, making it a popular choice among both amateur and professional users.

One of the standout features of the Poulan 411274 is its construction. Made from high-quality steel, it is engineered to withstand intense usage while delivering exceptional cutting performance. The sharpness of the teeth, combined with their design, enables smoother and quicker cuts, reducing the effort needed during operation.

The chain features a 3/8 inch pitch, which strikes an excellent balance between cutting speed and control. This pitch size is often favored for medium to large-sized chainsaws, providing a powerful cutting ability suitable for various tasks such as tree trimming, firewood cutting, and other light to medium forestry work.

An essential characteristic of the Poulan 411274 is its low kickback design. This feature is vital for user safety, as it minimizes the risk of kickback accidents, which can occur when the chain suddenly jerks back towards the user during cutting. The chain also incorporates a special heat treatment process that enhances its strength and wear resistance, ensuring it maintains its cutting edge longer and requires fewer replacements over time.

The technology behind the chain includes precision-engineered cutting teeth that significantly improve cutting efficiency. This design not only enhances performance but also reduces the amount of force required from the operator, thereby decreasing fatigue during prolonged use.

Ease of installation is another notable aspect of the Poulan 411274. It is designed to fit various Poulan chainsaw models as well as compatible devices, making it a versatile choice for users. The chain comes with pre-stretched links, ensuring it fits snugly without the need for extensive adjustments, allowing users to get back to work quickly.

Overall, the Poulan 411274,96042004201 chain combines durability, safety, and efficiency, making it an essential component for anyone looking to enhance their outdoor cutting tasks. Whether you're a weekend warrior or a professional in the field, this chain provides the reliability and performance needed for effective chainsaw operation.
Top Page Image Contents