Poulan 411274 manual Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)1/2" wrench Utility knife

(2)3/4" wrench Tire pressure gauge Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT WASHER

STEERING

WHEEL

STEERING BOOT

ADAPTER

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

TABS

EXTENSION SHAFT

TAB SLOTS

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

LOWER STEERING SHAFT

03132

FIG. 1

INSTALL SEAT (See Figs. 2 and 3)

•Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Remove the cardboard packing and discard.

•Connect switch to seat.

•Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

SEAT

SWITCH

PAD

SLOT

SEAT

PAN

TAPE

WIRING HARNESS

Fig. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB20H46LT ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemReverse Operation System ROS To Operate Mower See FigTowing Carts and Other ATTACH- Ments Before Starting the EngineTo Transport Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission RunningMaintenance To Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemBelts BatteryEngine Transaxle CoolingCleaning To Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Drive Belt See Fig To Replace Motion Belt Drive See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Page Page Degrés Suivant LES UNE Pliez EST CeciLimitée Garantie Dépannage DE Guide Défectueux estRalenti Entreposage DU Commande LA Régler PourGAZ DES Commande MoteurRéglages ET Révision Tionrecdi CarrossageAVANT/ Roues DES Convergence LA DE L’ALIGNEMENT Régler PourFreins LES Vérifier Pour Courroie Acer Rempl Pour’ENTRAÎNEMENT 25 .FIG21 .FIG Tondeuse LA Niveau LE Ajuster Pour22 .FIG 20 .FIG19 .FIG 17 .FIG 18 .FIG16 .FIG Tracteur Courroie LA ET Tondeuse LA InstallerReglages ET Revision Fig Voir’ALLUMAGE Bougie Ligne EN Installé D’ESSENCE FiltreEntretien AIR À FiltreTransmission LA DE Refroidissement LubrificationTrapézoïdales Courroies Fig la Voir Lame LA Affiler Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET Lubrification DE Tableau O I T a D N a M M O C E RGénérales Utilisation Chaque AvantTonte DE Conseils UtilisationTransmission LA Purger QuetiMoteur LE Démarrer DE Avant ROS Arrière CHE MAR EN Fonctionnement DE SystèmeTondeuse LA Utiliser Pour Tondeuse DE Lames LES Arrêter PourFig la Voir Mentne GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Tionsta DE Frein LE Engager PourTracteur Votre Connaissez Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier Fig la Voir Batterie LA Vérifier Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour DU Tracteur LE Sortir Pour LE Pour Exigés Outils LESMontar SIN Piezas Sommaire Client DU ResponsabilitésProduit DE Spécifications Enfants EntretienRemorquage Général EntretienGénéral Fonctionnement PentesLES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAUX Imprimé

96042004201, 411274 specifications

The Poulan 411274,96042004201 is a robust and efficient replacement chain designed for various outdoor power equipment, specifically chainsaws. This chainsaw chain is recognized for its remarkable performance and durability, making it a popular choice among both amateur and professional users.

One of the standout features of the Poulan 411274 is its construction. Made from high-quality steel, it is engineered to withstand intense usage while delivering exceptional cutting performance. The sharpness of the teeth, combined with their design, enables smoother and quicker cuts, reducing the effort needed during operation.

The chain features a 3/8 inch pitch, which strikes an excellent balance between cutting speed and control. This pitch size is often favored for medium to large-sized chainsaws, providing a powerful cutting ability suitable for various tasks such as tree trimming, firewood cutting, and other light to medium forestry work.

An essential characteristic of the Poulan 411274 is its low kickback design. This feature is vital for user safety, as it minimizes the risk of kickback accidents, which can occur when the chain suddenly jerks back towards the user during cutting. The chain also incorporates a special heat treatment process that enhances its strength and wear resistance, ensuring it maintains its cutting edge longer and requires fewer replacements over time.

The technology behind the chain includes precision-engineered cutting teeth that significantly improve cutting efficiency. This design not only enhances performance but also reduces the amount of force required from the operator, thereby decreasing fatigue during prolonged use.

Ease of installation is another notable aspect of the Poulan 411274. It is designed to fit various Poulan chainsaw models as well as compatible devices, making it a versatile choice for users. The chain comes with pre-stretched links, ensuring it fits snugly without the need for extensive adjustments, allowing users to get back to work quickly.

Overall, the Poulan 411274,96042004201 chain combines durability, safety, and efficiency, making it an essential component for anyone looking to enhance their outdoor cutting tasks. Whether you're a weekend warrior or a professional in the field, this chain provides the reliability and performance needed for effective chainsaw operation.
Top Page Image Contents