Poulan 96042004201, 411274 manual Transaxle Motion Control Lever Neutral Adjustment See Fig

Page 23

SERVICE AND ADJUSTMENTS

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL LEVER

NEUTRAL

 

LOCK GATE

ADJUSTMENT

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model PB20H46LTII. Slope Operation Safe Operation Practices for Ride-On MowersGeneral Operation IV. Towing ServiceIII. Children Table of Contents Contents of Hardware Pack Unpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsRunning Mowing TipsPurge Transmission Automatic Transmission Warm UPMaintenance Check Operator Presence System TractorBlade Removal See Fig To Sharpen Blade See FigTransaxle Cooling BatteryEngine BeltsCleaning To Remove Mower See Fig To Install Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Replace Motion Belt Drive See Fig Belt InstallationTo Replace Mower Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Page Page UNE Pliez EST Ceci Degrés Suivant LESLimitée Garantie Défectueux est Dépannage DE GuideRalenti Moteur DU Commande LA Régler PourGAZ DES Commande EntreposageRéglages ET Révision LA DE L’ALIGNEMENT Régler Pour CarrossageAVANT/ Roues DES Convergence Tionrecdi25 .FIG Courroie Acer Rempl Pour’ENTRAÎNEMENT Freins LES Vérifier Pour20 .FIG Tondeuse LA Niveau LE Ajuster Pour22 .FIG 21 .FIG16 .FIG 19 .FIG 17 .FIG18 .FIG Fig Voir Courroie LA ET Tondeuse LA InstallerReglages ET Revision TracteurAIR À Filtre Ligne EN Installé D’ESSENCE FiltreEntretien ’ALLUMAGE BougieTrapézoïdales Courroies Transmission LA DE RefroidissementLubrification EN Fonctionnement DE Système ET Fig la Voir Lame LA AffilerFig la Voir Lame LA Enlever Utilisation Chaque Avant O I T a D N a M M O C E RGénérales Lubrification DE TableauQueti UtilisationTransmission LA Purger Tonte DE ConseilsMoteur LE Démarrer DE Avant Tondeuse DE Lames LES Arrêter Pour MAR EN Fonctionnement DE SystèmeTondeuse LA Utiliser Pour ROS Arrière CHETionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Fig la Voir MentneTracteur Votre Connaissez Propriété la de lendommagement Toutes SI Vérifier Toutes SI Vérifier MontageCorrectement Sont Courroies LES LA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA VérifierDesmancom des tionfonc la et LE Pour Exigés Outils LES DU Tracteur LE Sortir PourMontar SIN Piezas Produit DE Spécifications SommaireClient DU Responsabilités Général Entretien EntretienRemorquage EnfantsTracteurs des sécurité toute en l’utilisation pour Conseils PentesLES Dans Fonctionnement Général FonctionnementAUX Imprimé

96042004201, 411274 specifications

The Poulan 411274,96042004201 is a robust and efficient replacement chain designed for various outdoor power equipment, specifically chainsaws. This chainsaw chain is recognized for its remarkable performance and durability, making it a popular choice among both amateur and professional users.

One of the standout features of the Poulan 411274 is its construction. Made from high-quality steel, it is engineered to withstand intense usage while delivering exceptional cutting performance. The sharpness of the teeth, combined with their design, enables smoother and quicker cuts, reducing the effort needed during operation.

The chain features a 3/8 inch pitch, which strikes an excellent balance between cutting speed and control. This pitch size is often favored for medium to large-sized chainsaws, providing a powerful cutting ability suitable for various tasks such as tree trimming, firewood cutting, and other light to medium forestry work.

An essential characteristic of the Poulan 411274 is its low kickback design. This feature is vital for user safety, as it minimizes the risk of kickback accidents, which can occur when the chain suddenly jerks back towards the user during cutting. The chain also incorporates a special heat treatment process that enhances its strength and wear resistance, ensuring it maintains its cutting edge longer and requires fewer replacements over time.

The technology behind the chain includes precision-engineered cutting teeth that significantly improve cutting efficiency. This design not only enhances performance but also reduces the amount of force required from the operator, thereby decreasing fatigue during prolonged use.

Ease of installation is another notable aspect of the Poulan 411274. It is designed to fit various Poulan chainsaw models as well as compatible devices, making it a versatile choice for users. The chain comes with pre-stretched links, ensuring it fits snugly without the need for extensive adjustments, allowing users to get back to work quickly.

Overall, the Poulan 411274,96042004201 chain combines durability, safety, and efficiency, making it an essential component for anyone looking to enhance their outdoor cutting tasks. Whether you're a weekend warrior or a professional in the field, this chain provides the reliability and performance needed for effective chainsaw operation.
Top Page Image Contents