Poulan 96042004201, 411274 manual Engine dies when

Page 27

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

Engine dies when

1.

Reverse operation system

1.

Turn ignition key to

tractor is shifted

 

(ROS) is not "ON" while

 

ROS "ON" position.

into reverse

 

mower or other attachment

 

See Operation section.

 

 

is engaged.

 

 

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves seat

 

 

 

corrected, contact an authorized service center/

with attachment clutch

 

 

 

department.

engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Light switch is “OFF”.

1.

Turn light switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Engine “backfires” when

1.

Engine throttle control not set between half and

1.

Move throttle control between half and full speed

turning engine “OFF”

 

full speed (fast) position before stopping engine.

 

(fast) position before stopping engine.

 

 

 

 

 

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model PB20H46LTSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack Unpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsRunning Mowing TipsPurge Transmission Automatic Transmission Warm UPMaintenance Check Operator Presence System TractorBlade Removal See Fig To Sharpen Blade See FigTransaxle Cooling BatteryEngine BeltsCleaning To Remove Mower See Fig To Install Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Replace Motion Belt Drive See Fig Belt InstallationTo Replace Mower Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Page Page UNE Pliez EST Ceci Degrés Suivant LESLimitée Garantie Défectueux est Dépannage DE GuideRalenti Moteur DU Commande LA Régler PourGAZ DES Commande EntreposageRéglages ET Révision LA DE L’ALIGNEMENT Régler Pour CarrossageAVANT/ Roues DES Convergence Tionrecdi25 .FIG Courroie Acer Rempl Pour’ENTRAÎNEMENT Freins LES Vérifier Pour20 .FIG Tondeuse LA Niveau LE Ajuster Pour22 .FIG 21 .FIG19 .FIG 17 .FIG 18 .FIG16 .FIG Fig Voir Courroie LA ET Tondeuse LA InstallerReglages ET Revision TracteurAIR À Filtre Ligne EN Installé D’ESSENCE FiltreEntretien ’ALLUMAGE BougieTransmission LA DE Refroidissement LubrificationTrapézoïdales Courroies Fig la Voir Lame LA Affiler Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET Utilisation Chaque Avant O I T a D N a M M O C E RGénérales Lubrification DE TableauQueti UtilisationTransmission LA Purger Tonte DE ConseilsMoteur LE Démarrer DE Avant Tondeuse DE Lames LES Arrêter Pour MAR EN Fonctionnement DE SystèmeTondeuse LA Utiliser Pour ROS Arrière CHETionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Fig la Voir MentneTracteur Votre Connaissez Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier Fig la Voir Batterie LA Vérifier Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour LE Pour Exigés Outils LES DU Tracteur LE Sortir PourMontar SIN Piezas Sommaire Client DU ResponsabilitésProduit DE Spécifications Général Entretien EntretienRemorquage EnfantsTracteurs des sécurité toute en l’utilisation pour Conseils PentesLES Dans Fonctionnement Général FonctionnementAUX Imprimé

96042004201, 411274 specifications

The Poulan 411274,96042004201 is a robust and efficient replacement chain designed for various outdoor power equipment, specifically chainsaws. This chainsaw chain is recognized for its remarkable performance and durability, making it a popular choice among both amateur and professional users.

One of the standout features of the Poulan 411274 is its construction. Made from high-quality steel, it is engineered to withstand intense usage while delivering exceptional cutting performance. The sharpness of the teeth, combined with their design, enables smoother and quicker cuts, reducing the effort needed during operation.

The chain features a 3/8 inch pitch, which strikes an excellent balance between cutting speed and control. This pitch size is often favored for medium to large-sized chainsaws, providing a powerful cutting ability suitable for various tasks such as tree trimming, firewood cutting, and other light to medium forestry work.

An essential characteristic of the Poulan 411274 is its low kickback design. This feature is vital for user safety, as it minimizes the risk of kickback accidents, which can occur when the chain suddenly jerks back towards the user during cutting. The chain also incorporates a special heat treatment process that enhances its strength and wear resistance, ensuring it maintains its cutting edge longer and requires fewer replacements over time.

The technology behind the chain includes precision-engineered cutting teeth that significantly improve cutting efficiency. This design not only enhances performance but also reduces the amount of force required from the operator, thereby decreasing fatigue during prolonged use.

Ease of installation is another notable aspect of the Poulan 411274. It is designed to fit various Poulan chainsaw models as well as compatible devices, making it a versatile choice for users. The chain comes with pre-stretched links, ensuring it fits snugly without the need for extensive adjustments, allowing users to get back to work quickly.

Overall, the Poulan 411274,96042004201 chain combines durability, safety, and efficiency, making it an essential component for anyone looking to enhance their outdoor cutting tasks. Whether you're a weekend warrior or a professional in the field, this chain provides the reliability and performance needed for effective chainsaw operation.
Top Page Image Contents