Poulan 411274, 96042004201 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 24

SERVICE AND ADJUSTMENTS

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

• Check wiring. See electrical wiring diagram in the

Repair Parts section.

FIG. 28

REPLACING BATTERY (See Figs. 29 and 30)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

03075

SEAT PAN

HEX

BOLT

 

FIG. 29

 

 

TERMINAL

KEPS NUT

COVER

 

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

 

 

 

FIG. 30

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair

24and/or adjustment.

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PB20H46LT ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack Tools Required for Assembly To Remove Tractor from CartonBefore Removing Tractor from Skid Unpack CartonCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System Reverse Operation System ROSTo Operate on Hills To Operate Mower See FigBefore Starting the Engine To TransportTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP RunningMaintenance Tractor Blade Removal See FigTo Sharpen Blade See Fig Check Operator Presence SystemBattery EngineBelts Transaxle CoolingCleaning To Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower Belt Installation To Replace Mower Drive Belt See FigTo Check Brake To Replace Motion Belt Drive See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Page Page Degrés Suivant LES UNE Pliez EST CeciLimitée Garantie Dépannage DE Guide Défectueux estRalenti DU Commande LA Régler Pour GAZ DES CommandeEntreposage MoteurRéglages ET Révision Carrossage AVANT/ Roues DES ConvergenceTionrecdi LA DE L’ALIGNEMENT Régler PourCourroie Acer Rempl Pour ’ENTRAÎNEMENTFreins LES Vérifier Pour 25 .FIGTondeuse LA Niveau LE Ajuster Pour 22 .FIG21 .FIG 20 .FIG19 .FIG 17 .FIG 18 .FIG16 .FIG Courroie LA ET Tondeuse LA Installer Reglages ET RevisionTracteur Fig VoirLigne EN Installé D’ESSENCE Filtre Entretien’ALLUMAGE Bougie AIR À FiltreTransmission LA DE Refroidissement LubrificationTrapézoïdales Courroies Fig la Voir Lame LA Affiler Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET O I T a D N a M M O C E R GénéralesLubrification DE Tableau Utilisation Chaque AvantUtilisation Transmission LA PurgerTonte DE Conseils QuetiMoteur LE Démarrer DE Avant MAR EN Fonctionnement DE Système Tondeuse LA Utiliser PourROS Arrière CHE Tondeuse DE Lames LES Arrêter PourGAZ DES Commande LA Utiliser Pour Fig la Voir Arrêter PourFig la Voir Mentne Tionsta DE Frein LE Engager PourTracteur Votre Connaissez Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier Fig la Voir Batterie LA Vérifier Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour DU Tracteur LE Sortir Pour LE Pour Exigés Outils LESMontar SIN Piezas Sommaire Client DU ResponsabilitésProduit DE Spécifications Entretien RemorquageEnfants Général EntretienPentes LES Dans FonctionnementGénéral Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAUX Imprimé

96042004201, 411274 specifications

The Poulan 411274,96042004201 is a robust and efficient replacement chain designed for various outdoor power equipment, specifically chainsaws. This chainsaw chain is recognized for its remarkable performance and durability, making it a popular choice among both amateur and professional users.

One of the standout features of the Poulan 411274 is its construction. Made from high-quality steel, it is engineered to withstand intense usage while delivering exceptional cutting performance. The sharpness of the teeth, combined with their design, enables smoother and quicker cuts, reducing the effort needed during operation.

The chain features a 3/8 inch pitch, which strikes an excellent balance between cutting speed and control. This pitch size is often favored for medium to large-sized chainsaws, providing a powerful cutting ability suitable for various tasks such as tree trimming, firewood cutting, and other light to medium forestry work.

An essential characteristic of the Poulan 411274 is its low kickback design. This feature is vital for user safety, as it minimizes the risk of kickback accidents, which can occur when the chain suddenly jerks back towards the user during cutting. The chain also incorporates a special heat treatment process that enhances its strength and wear resistance, ensuring it maintains its cutting edge longer and requires fewer replacements over time.

The technology behind the chain includes precision-engineered cutting teeth that significantly improve cutting efficiency. This design not only enhances performance but also reduces the amount of force required from the operator, thereby decreasing fatigue during prolonged use.

Ease of installation is another notable aspect of the Poulan 411274. It is designed to fit various Poulan chainsaw models as well as compatible devices, making it a versatile choice for users. The chain comes with pre-stretched links, ensuring it fits snugly without the need for extensive adjustments, allowing users to get back to work quickly.

Overall, the Poulan 411274,96042004201 chain combines durability, safety, and efficiency, making it an essential component for anyone looking to enhance their outdoor cutting tasks. Whether you're a weekend warrior or a professional in the field, this chain provides the reliability and performance needed for effective chainsaw operation.
Top Page Image Contents