Poulan 411287 manual Cleaning, IN-LINE Fuel Filter See Fig, Deck Washout Port See Fig

Page 18

MAINTENANCE

IN-LINE FUEL FILTER (See Fig. 14)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

•With engine cool, remove filter and plug fuel line sec- tions.

•Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

•Be sure there are no fuel line leaks and clamps are properly positioned.

•Immediately wipe up any spilled gasoline.

CLAMPCLAMP

FUEL

FILTER

FIG. 14

CLEANING

•Clean engine, battery, seat, finish, etc. of all foreign matter.

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

DECK WASHOUT PORT (See Fig. 15)

Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use.

1.Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.

IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached.

2.Make sure the PTO (Blade Engage) is not engaged, set the parking brake, and stop the engine.

3.Thread the nozzle adapter (packaged with your tractor’s Operator’s Manual) onto the end of your garden hose.

4.Pull back the lock collar of the nozzle adapter and push the adapter onto the deck washout port at the left end of the mower deck. Release the lock collar to lock the adapter on the nozzle.

HOSE

NOZZLE ADAPTER

WASHOUT

PORT

Fig. 15

IMPORTANT: Tug hose ensuring connection is secure.

5.Turn the water on.

6.While sitting in the operator’s position on the tractor, re-start the engine and place the throttle lever in the Fast " " position.

IMPORTANT: Recheck the area making certain the area is clear.

7.Move the tractor’s PTO (Blade Engage) to the ON position. Remain in the operator’s position with the cutting deck engaged until the deck is cleaned.

8.Move the tractor’s PTO (Blade Engage) to the OFF position. Turn the ignition key to the STOP position to turn the tractor’s engine off. Turn the water off.

9.Pull back the lock collar of the nozzle adapter to dis- connect the adapter from the nozzle washout port.

10.Move the tractor to a dry area, preferably a concrete or paved area. Engage the mower deck PTO to remove ex- cess water and to help dry before putting the tractor away.

WARNING: A broken or missing washout fitting could expose you or others to thrownobjectsfromcontactwiththeblade.

•Replace broken or missing washout fitting immediately, prior to using mower again.

•Pluganyholesinmowerwithboltsandlocknuts.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PB195H42LT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission RunningMaintenance Lubrication ChartBlade Removal See Fig BatteryTractor Important Special blade bolt is heat treatedEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Important Check Belt for Proper Routing ALL Mower Pulley GroovesCollar L onto guide and secure with retainer spring K To Level Mower To obtain the best cutting results, the mower blades shouldTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Alon THI Dotted Line REE LopeCanada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USADept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Degrés Dentretien Remarques Dépannage DE Guide Défectueux estRalenti DU Commande LA Régler Pour GAZ DES CommandeEntreposage DES L’AMPOULE Remplacer Pour Réglages ET RévisionFig la Voir Calandre LA ET Capot LE Enlever Pour Fig la Voir Batterie LA ReplacerCarrossage AVANT/ Roues DES Convergence TionrecdiLA DE L’ALIGNEMENT Régler Pour Tondeuse DE Lame DE Mentnetraî Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourFIG LA Voir ’EN Courroie LA Remplacer Pour22 .FIG Tondeuse LA Niveau LE Ajuster Pour24 .FIG 23 .FIG17 .FIG 20 .FIG 18 .FIG19 .FIG Place en bien est courroie la que vous-Assurez ImportantFig Voir Courroie LA ET Tondeuse LA InstallerReglages ET Revision Tondeuse LA Enlever PourFig La Voir Coupe DE Plateau DU Lavage DE Raccord Ligne EN Installé D’ESSENCE FiltreEntretien Fig la VoirMoteur DE D’HUILE Filtre ’ALLUMAGE BougieSilencieux AIR À FiltreFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETO I T a D N a M M O C E R Lubrification DE TableauUtilisation Chaque Avant Tonte DE Conseils UtilisationTransmission LA Purger 10 .FIG’ESSENCE Réservoir LE Remplir Accessoires AutresMoteur LE Démarrer Pour Moteur DU D’HUILE Niveau LE VérifierTracteur LE Transporter Pour Fig la Voir Tondeuse LA Utiliser PourMAR EN Fonctionnement DE Système Pentes LES Dans Utiliser PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Reculer Pour ET Avancer PourTracteur Votre Connaissez Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier Pour mentnetionfonc tionsec la Voir Fig la Voir Batterie LA VérifierDesmancom Des fonction la et mentceplalem connaître Rouler Faisant LE EN Palette LA DE Tracteur LE Retirer PourEt 2 .Figs les Voir Siège LE Ajustez DU Tracteur LE Sortir PourPour Exigés Outils LES Tionrecdi DE Volant LE FixerMontar SIN Piezas Garantie U1R DimensionSommaire CCA .MIN AMP/HR’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils Avertissement

411287 specifications

The Poulan 411287 is a robust outdoor power tool designed to meet the needs of homeowners and landscaping professionals alike. This high-performance gas-powered chainsaw is especially popular for its reliability, versatility, and user-friendly features, making it an ideal choice for both cutting firewood and tackling larger landscaping tasks.

One of the standout features of the Poulan 411287 is its powerful engine. Equipped with a 40cc two-stroke engine, this chainsaw delivers impressive performance while ensuring efficient fuel consumption. The engine's design minimizes emissions, aligning with contemporary environmental standards and making it a more eco-friendly option in the chainsaw market.

The chainsaw also incorporates a 16-inch steel bar and chain, providing ample cutting capacity for various applications. This length strikes a perfect balance, allowing users to handle everything from small branches to medium-sized trees without compromising ease of use. The bar and chain design ensures smooth cutting action, reducing kickback and improving operator safety.

Ergonomics play a crucial role in the Poulan 411287's design. The chainsaw is equipped with a comfortable grip that minimizes vibrations, making it less taxing on the user's hands during extended use. Additionally, the lightweight construction enhances maneuverability, allowing users to work for longer periods without fatigue.

Another noteworthy feature is the automatic chain oiler, which ensures the chain is consistently lubricated during operation. This not only prolongs the life of the chainsaw but also enhances cutting efficiency. The tool-less chain tensioning system further simplifies maintenance, allowing users to quickly adjust the chain for optimal performance without the need for additional tools.

Furthermore, the Poulan 411287 is designed with a translucent fuel tank, enabling users to monitor fuel levels at a glance. This convenient feature helps prevent unexpected interruptions during tasks, ensuring productivity is maximized.

In conclusion, the Poulan 411287 is a well-rounded chainsaw that combines power, ease of use, and innovative features. Whether for the occasional homeowner or the dedicated landscaping professional, it provides a reliable solution for a wide range of cutting tasks. With its focus on efficiency and user comfort, the Poulan 411287 is undoubtedly a valuable addition to any outdoor toolkit.
Top Page Image Contents