Poulan 411287 manual To Replace Mower Blade Drive Belt See Fig, To Check Brake, Belt Removal

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 25)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work belt around both mandrel pulleys and idler pulleys.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower (See "TO INSTALL MOWER" in this section of manual).

MANDRELIDLER

PULLEYPULLEYS

MANDREL

PULLEY

FIG. 25

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then the brakeneedstobeserviced.Contactaqualifiedservicecenter.

TO REPLACE MOTION DRIVE BELT (See Fig. 26)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler (A) and clutching idler (B).

•Remove belt from centerspan idler (C).

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (D).

•Remove belt downward from engine pulley (E).

•Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

•Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

•Pull belt toward front of tractor and roll belt onto engine pulley (E).

•Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (D). Be sure belt is inside the belt keeper.

•Install belt on centerspan idler (C).

•Install belt through stationary idler (A) and clutching idler (B).

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” section in this manual).

 

E

 

F

A

 

B

G

 

C

 

D

02952

22

FIG. 26

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PB195H42LT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission RunningMaintenance Lubrication ChartBlade Removal See Fig BatteryTractor Important Special blade bolt is heat treatedEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig ALL Mower Pulley Grooves Important Check Belt for Proper RoutingCollar L onto guide and secure with retainer spring K To Level Mower To obtain the best cutting results, the mower blades shouldTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Alon THI Dotted Line REE LopeCanada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAAutorisé Dept Service Customer Products Outdoor Canada AuGarantie cette de exclus sont normal l’entretien et Degrés Dentretien Remarques Dépannage DE Guide Défectueux estRalenti GAZ DES Commande DU Commande LA Régler PourEntreposage DES L’AMPOULE Remplacer Pour Réglages ET RévisionFig la Voir Calandre LA ET Capot LE Enlever Pour Fig la Voir Batterie LA ReplacerTionrecdi Carrossage AVANT/ Roues DES ConvergenceLA DE L’ALIGNEMENT Régler Pour Tondeuse DE Lame DE Mentnetraî Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourFIG LA Voir ’EN Courroie LA Remplacer Pour22 .FIG Tondeuse LA Niveau LE Ajuster Pour24 .FIG 23 .FIG17 .FIG 20 .FIG 18 .FIG19 .FIG Place en bien est courroie la que vous-Assurez ImportantFig Voir Courroie LA ET Tondeuse LA InstallerReglages ET Revision Tondeuse LA Enlever PourFig La Voir Coupe DE Plateau DU Lavage DE Raccord Ligne EN Installé D’ESSENCE FiltreEntretien Fig la VoirMoteur DE D’HUILE Filtre ’ALLUMAGE BougieSilencieux AIR À FiltreFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau O I T a D N a M M O C E RUtilisation Chaque Avant Tonte DE Conseils UtilisationTransmission LA Purger 10 .FIG’ESSENCE Réservoir LE Remplir Accessoires AutresMoteur LE Démarrer Pour Moteur DU D’HUILE Niveau LE VérifierTracteur LE Transporter Pour Fig la Voir Tondeuse LA Utiliser PourMAR EN Fonctionnement DE Système Pentes LES Dans Utiliser PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Reculer Pour ET Avancer PourTracteur Votre Connaissez Propriété la de lendommagement Correctement Sont Courroies LES MontageToutes SI Vérifier Toutes SI Vérifier Pour mentnetionfonc tionsec la Voir Fig la Voir Batterie LA VérifierDesmancom Des fonction la et mentceplalem connaître Rouler Faisant LE EN Palette LA DE Tracteur LE Retirer PourEt 2 .Figs les Voir Siège LE Ajustez DU Tracteur LE Sortir PourPour Exigés Outils LES Tionrecdi DE Volant LE FixerMontar SIN Piezas Garantie U1R DimensionSommaire CCA .MIN AMP/HR’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils Avertissement

411287 specifications

The Poulan 411287 is a robust outdoor power tool designed to meet the needs of homeowners and landscaping professionals alike. This high-performance gas-powered chainsaw is especially popular for its reliability, versatility, and user-friendly features, making it an ideal choice for both cutting firewood and tackling larger landscaping tasks.

One of the standout features of the Poulan 411287 is its powerful engine. Equipped with a 40cc two-stroke engine, this chainsaw delivers impressive performance while ensuring efficient fuel consumption. The engine's design minimizes emissions, aligning with contemporary environmental standards and making it a more eco-friendly option in the chainsaw market.

The chainsaw also incorporates a 16-inch steel bar and chain, providing ample cutting capacity for various applications. This length strikes a perfect balance, allowing users to handle everything from small branches to medium-sized trees without compromising ease of use. The bar and chain design ensures smooth cutting action, reducing kickback and improving operator safety.

Ergonomics play a crucial role in the Poulan 411287's design. The chainsaw is equipped with a comfortable grip that minimizes vibrations, making it less taxing on the user's hands during extended use. Additionally, the lightweight construction enhances maneuverability, allowing users to work for longer periods without fatigue.

Another noteworthy feature is the automatic chain oiler, which ensures the chain is consistently lubricated during operation. This not only prolongs the life of the chainsaw but also enhances cutting efficiency. The tool-less chain tensioning system further simplifies maintenance, allowing users to quickly adjust the chain for optimal performance without the need for additional tools.

Furthermore, the Poulan 411287 is designed with a translucent fuel tank, enabling users to monitor fuel levels at a glance. This convenient feature helps prevent unexpected interruptions during tasks, ensuring productivity is maximized.

In conclusion, the Poulan 411287 is a well-rounded chainsaw that combines power, ease of use, and innovative features. Whether for the occasional homeowner or the dedicated landscaping professional, it provides a reliable solution for a wide range of cutting tasks. With its focus on efficiency and user comfort, the Poulan 411287 is undoubtedly a valuable addition to any outdoor toolkit.
Top Page Image Contents